Debugger Interface
Debugger Main Window
43
Microcontrollers Debugger Manual
You can provide shortcuts for some of these functions using the toolbar. Refer to the
Debugger Main Window Toolbar
and
Customizing the Toolbar
sections for details.
You can also set breakpoints and watchpoints from within the Source and Assembly
component windows.
NOTE
For more information about breakpoints and watchpoints, refer to the
Control
Points
chapter.
Connection Menu
This menu entry (
Figure 2.17
) appears between the
Run
and
Component
menus when no
connection is specified in the
PROJECT.INI
file and no connection has been set. The
Connection
name is replaced by an actual connection name when the connection is set. If
a connection has been set, the number of menu entries is expanded, depending on the
connection. To set the connection, select
Component > Set Connection
. Refer to the
Component Menu
section for details.
Figure 2.17 Connection Menu
Table 2.5
describes the Connection Menu entries.
Assembly
Step Over
Similar to the
Step Over
command, but steps over subroutine call
instructions.
Shortcut:
CRTL + F10
keys
Assembly
Step Out
If the application is halted inside a function, this command continues
execution and stops on the CPU instruction following the current
function invocation. This command is similar to the
Step Out
command, but stops before the assignment of the result from the
function call.
Shortcut:
CTRL + Shift + F11 keys
Control Points
Opens the Controlpoints Configuration Window that contains tabs that
allow you to control Breakpoints, Watchpoints and Markpoints (refer to
Control Points
chapter).
Table 2.4 Run Menu Description (
continued)
Menu entry
Description
Summary of Contents for Microcontrollers
