Flexim FLUXUS F704**-A2 Series User Manual Download Page 122 | Manualshive

Page: 122 / 192

background image

13 Libraries

122

UMFLUXUS_F7V4-6-2EN, 2017-10-01

13.1.1

Data Retention During the Partitioning of the Coefficient Memory

When the coefficient memory is repartitioned, max. 8 data sets of each type can be retained.

13.2

Input of Material/Medium Parameters Without the Extended Library

To enter the material/medium parameters as constants, the extended library has to be deactivated.

The parameters of a user-defined material/medium can be entered now.
The input of a material or a medium is almost identical. Therefore, displays for a medium will only be shown and described
in case of differences.

The occupancy of the coefficient memory is displayed for a few seconds.

Select

yes

to start the partitioning. Press ENTER.

The coefficient memory is partitioned accordingly. This procedure takes a few seconds.

After the partitioning,

Format USER-AREA

is displayed again.

Example 1:

The number of user-defined materials is reduced from 5 to 3. The data sets #01 to #03 are retained.
The data sets #04 and #05 are deleted.

Example 2:

The number of user-defined materials is increased from 5 to 6. All 5 data sets are kept.

Select

Special Funct.\SYSTEM settings\Libraries\Extended Library

.

Press ENTER.

Select

off

to deactivate the extended library. Press ENTER.

Select

Special Funct.\Install Material

or

Install Medium

. Press ENTER.

This error message will be displayed if the coefficient memory does not contain an area for
user-defined materials/media.
Partition the coefficient memory accordingly (see section 13.1).

Select

edit

. Press ENTER.

Select a user-defined material/medium. Press ENTER.

Change the designation of the material/medium.
The default name for a user-defined material/medium is

USER MATERIAL N

or

USER ME-

DIUM N

with

N

being an integer.

Note!

95 ASCII characters (letters, capital letters, numbers, special characters [!? " + - ( ) > < % * etc.]) are
available for the designation of materials/media.
A designation can have max. 16 characters. The input of text is described in section 4.5.

USER AREA:

52% used

Format NOW?
no

>YES<

FORMATTING ...



...

Libraries

↕

Format USER-AREA

Libraries

↕

Extended Library

Extended Library
>OFF<

on

Special Funct.

↕

Install Material

USER Material
NOT FORMATTED !

Install Material
>EDIT<

delete

USER Material

↕

#01:--not used--

EDIT TEXT (

↑↓←

→



USER MATERIAL

1

«
...
120
121
122
123
124
...
»

Summary of Contents for FLUXUS F704**-A2 Series

































































































































































































Reviews:

No comments

Related manuals for FLUXUS F704**-A2 Series

Brand: Keithley Pages: 32

Brand: OHAUS Pages: 26

Brand: Hach Pages: 96

Brand: GE Pages: 35

Brand: Yamaha Pages: 24

Brand: Hanna Instruments Pages: 2

Brand: EUPRY Pages: 6

Brand: REED Pages: 4

OPTIFLUX 4040 C Series

Brand: KROHNE Pages: 20

Brand: U.S. Solid Pages: 30

OMCL-AC240TS-R3

Brand: Olympus Pages: 3

Brand: kruss Pages: 115

Brand: Circutor Pages: 48

Brand: Teledyne Pages: 85

WD-35606-00, WD-35606-05

Brand: Oakton Pages: 10

Brand: Fuji Electric Pages: 85

Brand: Ntron Pages: 29

Brand: Scaletron Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands