Fike 10-071 Installation Manual Download Page 49

Page: 49 / 76

4.0 INSTALLATION

UL S2203

Cheetah Xi 50 Installation Manual

4-7

P/N: 06-369

Rev 6, 09/2015

4.9.3

INSTALL OPTIONAL DACT

If the optional DACT (P/N 10-2528) is to be installed within the Cheetah Xi 50 enclosure, it must be installed
prior to installing the control board (See Exhibits 4-6 and 4-7).

The following general steps shall be used to install the DACT into the back-box:

1. Locate the four threaded press studs provided in the enclosure back-box for mounting the DACT (See

Exhibit 4-6) and install the four hex stand-offs (.625, F/F #6-32) supplied with the DACT onto the
threaded press studs.

2. Align the mounting holes provided in the four corners of the DACT with the stand-offs and secure in

place using the four #6-32 screws supplied with the DACT (See Exhibit 4-7).

Refer to the installation instructions supplied with the DACT for specific installation instructions.

BACK-BOX

DACT

INE

EAT

INE



Exhibit 4-6: DACT Mounting Location

DACT CARD

6-32 SCREWS

(QTY. 4)

Exhibit 4-7: DACT Mounting

Summary of Contents for 10-071













































































Search results

Summary of Contents for 10-071

Reviews:

Related manuals for 10-071

Brands by name

Popular brands

Fike 10-071, Installation Manual

Search results

Summary of Contents for 10-071

Reviews:

Related manuals for 10-071

Brands by name

Popular brands