Fike 10-071 Installation Manual Download Page 52 | Manualshive

Page: 52 / 76

background image

4.0 INSTALLATION

4-10

Cheetah Xi 50 Installation Manual

UL S2203

Rev 6, 09/2015

P/N: 06-369

FM

4.11 INSTALL BATTERIES

The Cheetah Xi 50 enclosure is capable of housing up to two (2) 18 AH batteries. Where larger or additional
battery Amp-Hours are required, a separate battery cabinet can be installed to house the batteries. The
battery cabinet must be installed in the same room as the control panel with a maximum wire length of 10 ft.
(3 m). Interconnect wiring shall be 14 AWG minimum and shall be installed in conduit.

The following general steps shall be used to install the batteries:

1. Install the batteries (2) into bottom of the enclosure and/or into the separate battery cabinet.

2. Connect the positive (+) battery cable lead from the (P1) positive battery input terminal to the positive

(+) terminal of the first battery.

3. Connect the negative (-) battery cable lead from the (P1) negative battery input terminal to the

negative (-) terminal of the second battery.

4. A jumper is supplied to provide the connection between the negative (-) terminal on the first battery to

the positive (+) terminal on the second battery.

Do NOT install this jumper at this time!

4.11.1 BATTERY CUTOFF

The  Cheetah  Xi  50  panel has battery cutoff feature that allows the system batteries to be automatically
disconnected from the load if the system’s operating voltage (AC/DC) drops below 19 volts. This feature
prevents the batteries from being discharged beyond their end-of-discharge terminal voltage thus preventing
potential damage to the batteries or control unit, which could result in abnormal operation of the control unit
during battery discharge period or on re-energizing by the main power supply.  Upon restoration of the main
power supply, the batteries shall be automatically reconnected to the system.  Refer to Appendix D for battery
cutoff wiring diagram.

P1

F1
AC
15A

F2

15A

(First)

12 VDC

BATTERY

R

ED

(

+)

B

L

A

C

K

(

-)

JUMPER

(Second)

12 VDC

BATTERY

(-)

(+)

(+)

(-)

Exhibit 4-11: Battery Connections

«
...
50
51
52
53
54
...
»

Summary of Contents for 10-071













































































Reviews:

No comments

Related manuals for 10-071

Brand: Febco Pages: 4

Brand: Cisco Pages: 48

Brand: TCS Basys Controls Pages: 2

DBI SALA Pro Series

Brand: 3M Pages: 24

medialon Showmaster Go

Brand: 7th Sense Pages: 2

Brand: Eaton Pages: 6

Brand: Eaton Pages: 35

Brand: Eaton Pages: 18

Brand: Eaton Pages: 73

Brand: Eaton Pages: 4

Cutler-Hammer IQ DP-4000

Brand: Eaton Pages: 87

Brand: Eaton Pages: 14

Brand: Eaton Pages: 36

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

GRAVIMETRIC AUGER FEEDER MGF-ST

Brand: Maguire Products Pages: 47

Brand: Magtrol Pages: 160

Brand: Rabbit Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands