Fike 10-071 Installation Manual Download Page 50

Page: 50 / 76

4.0 INSTALLATION

4-8

Cheetah Xi 50 Installation Manual

UL S2203

Rev 6, 09/2015

P/N: 06-369

4.9.4

INSTALL THE CHEETAH XI 50 CONTROLLER

The following general steps shall be used to install the Cheetah Xi 50 controller:

1. Locate the four threaded press studs provided in the enclosure back-box for mounting the controller

board (See Exhibit 4-8) and install the four hex stand-offs (2.5”, M/F #6-32) supplied with the
enclosure onto the threaded press studs.

2. Locate the threaded press studs provided in the enclosure back-box for keypad support (See Exhibit

4-9) and install the hex stand-off (2.5”, F/F #6-32) supplied with the enclosure onto the threaded
press stud.

3. Align the mounting holes provided in the four corners of the controller board with the stand-offs and

secure in place using the four #6-32 hex nuts supplied with the enclosure (See Exhibit 4-9).

JTAG

P10

24V

10-2620 REV
02-11544 REV A

CYBER CAT 50

FIKE CORPORATION
01:39:37A 06/14/2011

AL:000 SU:000 TR:000

BACK-BOX

CONTROLLER



Exhibit 4-8: Controller Mounting Location

2" F/F STANDOFF

(KEYPAD SUPPORT)

Exhibit 4-9: Controller Mounting

2.5” M/F STANDOFF
(TYP. 4 PLCS)

2.5” F/F STANDOFF
(KEYPAD SUPPORT)

Summary of Contents for 10-071













































































Search results

Summary of Contents for 10-071

Reviews:

Related manuals for 10-071

Brands by name

Popular brands

Fike 10-071, Installation Manual

Search results

Summary of Contents for 10-071

Reviews:

Related manuals for 10-071

Brands by name

Popular brands