Fike 10-071 Installation Manual Download Page 11 | Manualshive

Page: 11 / 76

background image

1.0 INTRODUCTION

UL S2203

Cheetah Xi 50 Installation Manual

1-3

FM

P/N: 06-369

Rev 6, 09/2015

1.5

RELATED DOCUMENTATION

To obtain a complete understanding of the specific features of the Cheetah Xi 50 or to become familiar with
related functions in general, refer to the documentation listed below. Please reference the most current
version or the version noted on the label located on the product.

Exhibit 1-1: Related Documentation

Document Title

Part Number

Device Compatibility Document

06-186

DACT (P/N 10-2528 & 10-2476) Installation Instructions

06-479

Remote Display Unit Product Manual (RDU2, RDU10 and RDU14)

06-610

Ethernet Module (P/N 10-074) Product Manual

06-388

Multi-Interface Module (P/N 10-2583) Product Manual

06-367

Intelligent Graphic Annunciator Product Manual

06-231

Twenty Zone Remote Annunciator (P/N 10-2667) Product Manual

06-453

Relay Control Assembly (P/N 10-2777) Installation Instructions

06-580

HPM4 Relay Module (P/N 10-2770) Installation Instructions

06-443

CRM4 Relay Module (P/N 10-2204) Installation Instructions

06-345

Relay Card (P/N 10-2785) Installation Instructions

06-586

3 Card Remote Equipment Enclosure (P/N 10-2780) Installation Document

06-590

5 Card Remote Equipment Enclosure (P/N 10-2781) Installation Document

06-591

Class A Peripheral Bus Card (P/N 10-2792) Installation Instructions

06-606

Class A Peripheral Bus Card Assembly (P/N 10-080) Installation Instructions

06-609

Solenoid Supervision and Protection Assembly (P/N 10-2360) Installation

06-344

Masterbox Supervisor (P/N 10-2413) Installation Instructions

06-229

VESDA Network Interface (P/N 68-023) Product Manual

06-158

Hand Held Programmer (P/N 10-2648) Operating Instructions

06-390

C-Linx Panel Configuration Software Manual

06-327

33 AH Battery Enclosure Installation Instructions

06-534

75 AH Battery Enclosure Installation Instructions

06-535

50 Point Enclosure Installation Instructions

06-624

50 Point Dead-Front Panel Installation Instructions

06-647

50 Point Controller Installation Instructions

06-427

Agent Release Module (ARM III)

06-106

Impulse Release Module (IRM)

06-552

Surge Suppressor Compatibility Document

06-588

Suppression Disconnect Switch (P/N 10-2698 & 10-2699)

06-472

«
...
9
10
11
12
13
...
»

Summary of Contents for 10-071













































































Reviews:

No comments

Related manuals for 10-071

Brand: ZKTeco Pages: 18

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

Brand: Campbell Pages: 8

Brand: Daikin Pages: 2

Brand: Daikin Pages: 12

Brand: Daikin Pages: 12

Brand: Daikin Pages: 46

Brand: Daikin Pages: 21

Brand: Daikin Pages: 20

Brand: Fagor Pages: 10

Brand: Fagor Pages: 358

Brand: Fagor Pages: 556

Brand: Fagor Pages: 172

Brand: Fagor Pages: 180

Brand: Fagor Pages: 112

Master Control Unit

Brand: FaderMate Pages: 36

Brand: RadioMaster Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands