Fike 10-071 Installation Manual Download Page 70

Page: 70 / 76

APPENDIX C

C-2

Cheetah Xi 50 Installation Manual

UL S2203

Rev 6, 09/2015

P/N: 03-369

Exhibit C-2: Compatible Components – Cont.

Part Number

Description

INTELLIGENT DETECTORS

63-1052

Photoelectric Detector

67-033

Ionization Detector

63-1053

Photo/135° F Heat Combination Detector

60-1039

Intelligent Heat Detector, 135°-190° F (57°-88° C) Fixed Temp./ Rate of Rise

63-1054 (EBF)

Detector Base, 6 inch (System Sensor)

63-1055 (EB)

Detector Base, 4 inch (System Sensor)

63-1064 (EBS)

Sounder Base, 6 inch (System Sensor)

63-1063 (EBR)

Relay Base, 6 inch (System Sensor)

63-1058

Photo Detector, with Isolator

67-034

Ionization Detector, with Isolator

63-1059

Photo/135° F Heat Combination Detector, with Isolator

60-1040

Heat Detector, 135°-190° F (57°-88° C) Fixed Temp./ Rate of Rise, with Isolator

63-1060 (EBFI)

Detector Base, 6 inch, with Isolator (System Sensor)

63-1061 (EBI)

Detector Base, 4 inch, with Isolator (System Sensor)

63-1057

Photo DUCT detector

63-1062

Photo DUCT detector, with Isolator

63-1158

DUCT Detector Housing (must be used with 63-1057 & 63-1062)

68-140

FAAST Aspirating Smoke Detector

68-302

FAAST XT Aspirating Smoke Detector

DUCT DETECTOR ACCESSORIES

02-3868

Remote Annunciator LED

02-3869

Remote Test Station

02-4998

Remote Test Station with Key

63-1159

Sampling Tube, Duct Detector, up to 1 ft. (0.3m)

63-1160

Sampling Tube, Duct Detector, 1 ft. to 2 ft. (0.3m – 0.6m)

63-1161

Sampling Tube, Duct Detector, 2 ft. to 4 ft. (0.6m – 1.2m)

63-1162

Sampling Tube, Duct Detector, 4 ft. to 8 ft. (1.2m – 2.4m)

63-1163

Sampling Tube, Duct Detector, 8 ft. to 12 ft. (2.4m – 3.7m)

ADDRESSABLE MODULES

55-045

Mini Monitor Module (MMM)

55-041

Monitor Module (MM), 4 inch

20-1063

Addressable Pull Station (APS)

55-042

Supervised Control Module (SCM)

10-2360

Series Solenoid Diode/Resistor

10-2413

Master-box Interface

55-043

Relay Module (RM)

55-052

Releasing Control Module (RCM)

55-050

Mini Monitor Module (MMM), with Isolator

55-046

Monitor Module (MM), 4 inch, with Isolator

20-1064

Addressable Pull Station (APS), with Isolator

55-047

Supervised Control Module (SCM), with Isolator

55-048

Relay Module (RM), with Isolator

55-053

Releasing Control Module (RCM), with Isolator

Summary of Contents for 10-071













































































Search results

Summary of Contents for 10-071

Reviews:

Related manuals for 10-071

Brands by name

Popular brands

Fike 10-071, Installation Manual

Search results

Summary of Contents for 10-071

Reviews:

Related manuals for 10-071

Brands by name

Popular brands