Fike 10-071 Installation Manual Download Page 43 | Manualshive

Page: 43 / 76

background image

4.0 INSTALLATION

UL S2203

Cheetah Xi 50 Installation Manual

4-1

FM

P/N: 06-369

Rev 6, 09/2015

4.1

SYSTEM INSTALLATION SEQUENCE

This section provides general instructions that should be adhered to when installing the Cheetah Xi 50
system. Refer to the installation instruction sheets supplied with each component for specific installation
instructions.

The following checklist is provided to assist the installer during system installation:

Task

Refer to

Select the enclosure mounting location.

Section 4.2

Select the enclosure mounting option (flush or surface).

Section 4.3

Mount the enclosure.

Section 4.4

Wire Selection

Section 4.5

Circuit Class Designations

Section 4.6

Pull field wiring into enclosure.

Section 4.7

Verify the field wiring.

Section 4.8

Install internal panel components.

Section 4.9

Connect AC power to the controller.

Section 4.10

Install batteries.

Section 4.11

Apply power to the panel.

Section 4.12

Connect field wiring.

Section 4.13

Initial power-up with field wiring connected.

Section 4.14

Configure the system.

Section 4.15

Conduct acceptance testing.

Section 4.16

Install the dead-front panel.

Section 4.17

4.2

SELECT THE ENCLOSURE MOUNTING LOCATION

The mounting location for the Cheetah Xi 50 enclosure is very important. Fike recommends that all system
enclosures be installed in an area that is readily accessible with sufficient room to allow easy installation and
maintenance, and that is capable of maintaining a nominal room temperature of 0°-49°C / 32°-120°F, with a
relative humidity of 93 percent. Do NOT install in an environment that exceeds these temperature and
humidity ranges.

Additional items to consider when selecting the appropriate mounting location for the enclosure includes:
vibration, dust, moisture, electromagnetic interference, and radio frequency interference. These are all types
of problems that could adversely effect the successful operation and useful life of the electronic components
and should be avoided if possible.

Mount the enclosure at a height that allows easy access to system electronic components for maintenance
and service. Allow sufficient clearance around the enclosure for the outer door to swing freely.

«
...
41
42
43
44
45
...
»

Summary of Contents for 10-071













































































Reviews:

No comments

Related manuals for 10-071

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: HAMTRONICS Pages: 8

Brand: National Instruments Pages: 31

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 98

CompactRIO cRIO-9002

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 145

Brand: National Instruments Pages: 42

Brand: National Instruments Pages: 8

Brand: National Instruments Pages: 54

Brand: Paradox Pages: 32

Brand: KaRo Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands