Fike 10-071 Installation Manual Download Page 72

Page: 72 / 76

APPENDIX C

C-4

Cheetah Xi 50 Installation Manual

UL S2203

Rev 6, 09/2015

P/N: 03-369

Exhibit C-4: Compatible Components – Cont.

Part Number

Description

SPARE PARTS

02-4035

Hardware Kit, #6 lock washers and hex nuts (30 each)

02-10788

Standoff kit, 5/8” M/F, 5 each required for DACT (10 each supplied)

02-4009

Standoff, 2” M/F, for Cheetah Xi 50 controller, 4 each required (1 each supplied)

02-11751

Standoff, 2” F/F, for Cheetah Xi 50 controller, 1 each required (1 each supplied)

02-11823

Key lock with cam

02-4983

Panel Key Only (without cam)

02-10881

Transformer, 120VAC

02-10882

Transformer, 240 VAC

02-4040

Battery, Lithium Coin Cell, 3V

10-2625

Monitor and Control Module EOL Assembly, 39K

10-2530

14KΩ Series Resistor, for Monitor Module Short Circuit detection

10-2570

End of Line Resistor, 1.2 K (for NAC 1 & 2)

02-4174

Fuse, 15 Amp, Mini-Auto, Fast Acting (For F1 & F2) (Little fuse p/n 297015)

02-11412

Fuse, 4 Amp, Mini-Auto, Fast Acting (For F3-5) (Little fuse p/n 297004)

02-4981

End Of Line Relay – System Sensor EOLR-1

02-2519

Termination Resistor, 100 ohm (for RS485 circuit)

02-11723

Bezel, Outer Door

C.1.1

TOUCH-UP PAINT (NOT AVAILABLE FROM FIKE)

Sherwin Williams, Signal Red – RAL 3001 per RAL 840-HR (Matt Finish)

Sherwin Williams, Light Gray – RAL 7035 per RAL 840-HR

C.1.2

NOTIFICATION APPLIANCES

Refer to Fike document 06-186 for compatible notification appliances.

C.1.3

APPROVED RELEASING DEVICES

Refer to Fike document 06-186 for compatible releasing devices.

Summary of Contents for 10-071













































































Search results

Summary of Contents for 10-071

Reviews:

Related manuals for 10-071

Brands by name

Popular brands

Fike 10-071, Installation Manual

Search results

Summary of Contents for 10-071

Reviews:

Related manuals for 10-071

Brands by name

Popular brands