![background image](http://html.mh-extra.com/html/fendt/916-vario/916-vario_operating-manual_552662011.webp)
11
SAFETY INSTRUCTIONS
Maintenance
Text-module
ETNum-list
1. Before maintenance and repair work, switch
off the engine and remove the ignition key.
Relieve pressure from implement lines, e.g. to
the front loader.
2. Any person should keep clear of a lifted,
unsecured load (e.g. tilted cab and similar).
3. Never open or remove any protection devices
while the engine is running.
4. Never grasp leaking pressure lines.
Pressurised fluids (diesel or hydr. oil) escaping
under high pressure can penetrate the skin
and cause severe injuries. If this has occurred,
seek medical advice at once to avoid the risk
of serious infection.
5. Keep at a safe distance from hot areas.
6. Hydraulic accumulator and connected pipes
are highly pressurised. Only remove and
repair in accordance with instructions provided
in Technical Manual.
7. To avoid eye injury, do not look directly at the
surface of the activated radar sensor.
8. Dispose of oil, fuels and filters properly!
9. For fitting tires, specialist knowledge and
special mounting tools are required.
10. Run the tractor for a short time, then
retighten all wheel nuts and bolts; check
them regularly. For correct torque values
refer to TECHNICAL DATA.
11. Before working on the electrical system,
always remove the ground strap from the
battery. Observe the following, when carrying
out electric welding. When carrying out
electric welding on tractor or mounted
implements, make sure that both battery
terminals are disconnected. Attach the
ground terminal as close as possible to the
welding point.
12. Spare parts must at least meet the technical
requirements stated by the manufacturer.
You can ensure that this is the case by using
genuine spare parts!
Text-module
ETNum-list
Advice for front loader maintenance:
1. Before undertaking maintenance work, lower
the front loader to the ground, switch off the
engine and remove the ignition key.
2. If the pipe fracture protection has engaged,
support the load before starting repairs, and
slowly retract the cylinder.
3. Hydraulic hoses deteriorate with age. Check
the condition of hydraulic hoses at regular
intervals, and replace them in good time.
4. After attachment and repair operations, drive
the tractor for a short time then retighten all
mounting screws and nuts and check them
regularly.
5. Retighten eccentric bolt for front loader
attachment, if necessary.
Summary of Contents for 916 Vario
