![background image](http://html.mh-extra.com/html/fendt/916-vario/916-vario_operating-manual_552662237.webp)
237
FAULTS AND REMEDIAL ACTIONS
Text-module
6.1.05
PTO shaft rpm sensor faulty.
PTO can only be switched on/off with the
cab button. Button must be pressed for at
least 5 secs.
6.1.10
Speed sensor shaft faulty.
6.1.11
Automatic mode on operating
console faulty.
Automatic mode is ended and PTO dis-
engages.
6.1.15
Neutral speed selection key
faulty.
Does not function, PTO disengages.
6.1.16
Selection range key 540 faulty. No function of range selection key 540.
6.1.17
Setting 540E selection button
faulty.
Setting 540E selection button does not
function.
6.1.18
Speed selection key 1000
faulty.
No function of speed selection key 1000.
6.1.1A
Setting 540 valve faulty.
Does not function, PTO disengages.
6.1.1B
Control valve 540E faulty.
Does not function, PTO disengages.
6.1.1C
Control valve 1000 faulty.
Does not function, PTO disengages.
6.1.41
Cab button plausibility error.
Does not function, PTO disengages.
6.1.42
Right mudguard button plausi-
bility error.
Does not function, PTO disengages.
6.1.43
Left mudguard button plausibi-
lity error.
Does not function, PTO disengages.
6.1.45
PTO clutch rpm sensor plausi-
bility error.
PTO can only be operated via keys inside
the cab, key must be kept pressed for at
least 5 secs.
6.1.50
Speed sensor PTO shaft plau-
sibility error.
When engaging, the button must be pres-
sed for at least 5 secs.
6.1.55
Plausibility error in speed se-
lection key neutral.
Does not function, PTO disengages.
6.1.56
Plausibility error in speed se-
lector key 540.
No function of 540 selection.
6.1.57
540E setting pre-selection but-
ton plausibility error.
No function of 540E selection.
6.1.58
Plausibility error in speed se-
lection key 1000.
No function of 1000 selection.
6.1.60
Plausibility error between PTO
clutch rpm and PTO stub shaft
speed.
Does not function, PTO disengages.
6.1.BO
Initialisation error on communi-
cation driver. CAN bus commu-
nication restricted.
EOL programming.
6.1.C1
Switch-on speed not reached
for PTO/power lift automatic
mode.
Increase ground speed to more than
1 km/h.
6.1.EO
Checksum parameter current
control for range shifting faulty.
EOL programming.
6.1.E1
Checksum PTO parameter
faulty.
EOL programming.
Fault code
Cause
Effect and remedy
Summary of Contents for 916 Vario
