![background image](http://html.mh-extra.com/html/fendt/916-vario/916-vario_operating-manual_552662160.webp)
160
CARE AND MAINTENANCE
20. Electrical and elec-
tronic systems
Since even a test lamp can damage electronic
components in the electrical system, trouble
shooting must always be carried out in the work-
shop.
Disconnect battery if the tractor is not used for
long periods, to prevent it being discharged by
small consumers. Check the battery charge level
every 2 months. Do not operate the tractor wit-
hout a battery.
Text-module
In the following conditions, stored settings (for
example, the speed indicator setting) are lost
and are replaced by the default values:
ETNum-list
20.1 Battery
Operation_Pic_number:1
Acid level approx. 15 mm above the top of the
plates.
●
Top up with distilled water when necessary.
Not necessary with sealed batteries. Keep bat-
tery clean!
Keep battery in good charging condition - espe-
cially in cold weather.
Do not operate the tractor without a battery.
1. Drained or disconnected battery.
2. White connector 1 disconnected from
instrument cluster.
WARNING:
When working on the electrical
system, always disconnect the
battery (negative terminal).
Use the correct connecting
sequence - connect first plus
terminal and then minus terminal.
Beware of battery acid caustic!
Beware of battery gases!
Avoid sparks and naked flame near
the battery. The glass on work lamps
are very hot while switched on!
Fig.62
20.2 Alternator
Charge control lamps go out after starting at ap-
prox. 1,000 rpm.
20.3 Electrowelding
Disconnect both battery terminals. Keep ground
terminal as close to the point of welding as pos-
sible; be aware of components sensitive to tem-
perature.
20.4 Adjusting the headlights
Operation_Pic_number:1
●
Adjust headlights using the Phillips screws
(arrows).
CAUTION:
Before adjusting, bring the tractor
front axle suspension to centre
position of the total suspension
range (see also OPERATION
Section 13).
Fig.63
Summary of Contents for 916 Vario
