XTP II CrossPoint Series • Front Panel Operation
37
Ethernet to RS-232 Insertion
Ethernet to RS-232 insertion allows control of a device from a remote location over the Ethernet
network. For example, an Extron IPCP control processor, connected to the matrix switcher LAN
connecter, controlling a camera, connected to an XTP transmitter which is connected to an XTP
input connector in the matrix switcher (see below).
100-240V
DISCONNECT POWER
CORD BEFORE
SERVICING
50-60Hz
12.0A MAX
1−4
5−8
9−12
13−16
1−4
5−8
9−12
13−16
OUTPUT
S
XTP CROSSPOINT 1600
INPUT
S
OUTPUTS
XTP CP 4o SA
AUDIO
L
R
L
R
L
R
L
R
INPUTS
XTP CP 4i VGA
AUDIO
L
R
L
R
L
R
L
R
INPUTS
XTP CP 4i 4K
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
XTP IN
PWR
LAN
SIG
LINK
XTP IN
PWR
LAN
SIG
LINK
XTP IN
PWR
LAN
SIG
LINK
XTP IN
PWR
LAN
SIG
LINK
OVER XTP
OUTPUTS
XTP CP 4o 4K
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
XTP OUT
PWR
LAN
SIG
LINK
XTP OUT
PWR
LAN
SIG
LINK
XTP OUT
PWR
LAN
SIG
LINK
XTP OUT
PWR
LAN
SIG
LINK
OVER XTP
INPUTS
AUDIO
L
R
L
R
L
R
L
R
XTP CP 4i HD 4K PLUS
OUTPUTS
AUDIO
L
R
L
R
L
R
L
R
XTP CP 4o HD 4K PLUS
RESET
REMOTE
LAN
RS-232/422
OUTPUTS
SIG
LINK
XTP OUT
LAN
LAN
LAN
LAN
SIG
LINK
XTP OUT
SIG
LINK
XTP OUT
SIG
LINK
XTP OUT
OVER FIBER
XTP CP 4o FIBER 4K
RS-232
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
INPUTS
SIG
LINK
XTP IN
LAN
LAN
LAN
LAN
SIG
LINK
XTP IN
SIG
LINK
XTP IN
SIG
LINK
XTP IN
OVER FIBER
XTP CP 4i FIBER 4K
RS-232
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
INPUTS
XTP CP 4i 4K
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
RS-232 IR
Tx Rx G Tx Rx
XTP IN
PWR
LAN
SIG
LINK
XTP IN
PWR
LAN
SIG
LINK
XTP IN
PWR
LAN
SIG
LINK
XTP IN
PWR
LAN
SIG
LINK
OVER XTP
POWER
12V
HDMI
0.7A MAX
Rx G
Tx
RS-232
IR
Rx
Tx
−
+
−
+
L
R
LOOP THRU
RESET
AUDIO
OFF
ON
AUDIO
XTP T HD 4K
LAN
SIG LINK
XTP OUT
INPUTS
OVER XTP
AV
LAN
1.2A MAX
100-240V ~ 50-60Hz
PWR OUT = 12W
+V +S -S G
1
4
2
3
7
5
6
8
S G S G
S G S G
Tx Rx G Tx Rx G Tx Rx G Tx Rx G RTSCTS
1
2
1
2
3
4
1
2
3
4
3
2
1
4 G
LAN
Tx Rx G Tx Rx G Tx Rx G Tx Rx G RTS CTS
S G S G
S G S G
5
6
7
8
5
6
7
8
SWITCHED 12 VDC
40W MAX TOTAL
3
4
COM
eBUS
FLEX I/O
RELAYS
IR/SERIAL
12 VDC
Extron
XTP CrossPoint 1600
Modular Digital Matrix Switcher
Extron
IPCP PRO 555
IP Link Pro
Control Processor
Extron
XTP T HD 4K
XTP Transmitter for HDMI
Ethernet
RS-232
Network
RS-232
HD Camera
Figure 23.
Typical Ethernet to RS-232 Insertion
Each XTP twisted pair or fiber input and output connector on the matrix switcher has a
dedicated UART port number. The number of XTP inputs and outputs determine the total
number of available ports. To determine the numbers for the ports, set a starting number for the
RS-232 and RS-422 connector. Each additional input starts numbering sequentially after two
numbers greater than the starting value. Each output starts numbering sequentially after the
maximum number of possible inputs (33 for 1600 and 3200 models, and 65 for 6400 models).
To change the starting point, use the XTP System Configuration Software (see the
XTP System
Configuration Software Help
file).
NOTE:
Ensure the RS-232 protocol matches the connected device. To do this, use the XTP
System Configuration Software (see the
XTP System Configuration Software Help
file).
