Eurotech ZyWAN User Manual Download Page 107

Page: 107 / 130

PART 2: SOFTWARE CONFIGURATION

107

110150-1001F

Use WinSCP to connect to the ZyWAN, and browse to its

/tmp/

(or

/var/tmp/

) folder. Download the

“Zywan-1.

to1.

update.tar” file to the ZyWAN as shown in the following screen capture.

After the files are loaded, connect to the ZyWAN using either HyperTerminal on the COM1 diagnostics port

or over the network using PuTTY (or another SSH application). See the section

Setting Up Software

page

, for help setting up HyperTerminal or PuTTY.

From the ZyWAN command line, issue the following commands:

cd /var/www/updates

tar xvf /tmp/Zywan-1.2to1.5update.tar

tar xvf /tmp/Zywan-1.4to1.5update.tar

touch /tmp/update.log

tail -f /tmp/update.log &

(Notice the ampersand ‘&’ at the end.)

touch /tmp/update

A series of diagnostic messages will be displayed, ending with a system reboot. If updating from version 1.2,

there will also be a reboot after completing the 1.4 update. The following screen captures show these

messages.

Summary of Contents for ZyWAN



































































































































Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands

Eurotech ZyWAN, User Manual

Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands