Eurotech ZyWAN User Manual Download Page 128

Page: 128 / 130

ZyWAN - User Manual

128

110150-1001F

Radio Frequency Standards for ZyWAN-IDEN (IO270)

FCC ID: UFNZEUSIO270

FCC grant information: Products operating with this OEM module must not exceed 2.54 W EIRP total system

output with antenna gain not exceeding 7.3dBi. The antenna must operate at 20 cm or more from persons.

This module is not approved for use in any products operating as a portable transmitter with respect to

2.1093 or other mobile operating conditions that do not meet categorical exclusion requirements of 2.1091,

which requires separate approval.

Radio Frequency Standards for ZyWAN-GPRS (GR64)

FCC ID: UFNZEUSGR64

FCC grant information: This device is approved for mobile RF exposure conditions. Approved for use with

antenna(s) as listed in this filing. The antenna(s) used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction

with any other antenna or transmitter.

Radio Frequency Standards for ZyWAN with 802.11

FCC ID: UFNZEUSPN18

FCC grant information: Modular Approval for mobile RF exposure conditions, the antenna(s) used for this

transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not

be co-located or operating in conjunction with any other antenna or transmitter. The only antennas approved

for use with this module are those documented in the filings under this FCC ID.

Summary of Contents for ZyWAN



































































































































Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands

Eurotech ZyWAN, User Manual

Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands