Eurotech ZyWAN User Manual Download Page 121

Page: 121 / 130

PART 3: CONFIGURATION EXAMPLES

121

110150-1001F

Configuration Example 3: Terminal Server

The Terminal Server configuration example illustrates the following features of the ZyWAN:

•

Terminal Server for IP to serial conversion, allowing host applications to communicate with a local

serial device

The following table lists the network settings used in this example, which is only a partial configuration to

illustrate the Terminal Server network.

SETTING

DETAILS

Terminal Server

IP port 4000 will be set up as a Terminal Server, which will redirect

data to the COM2 port.

Networking

Open port 4000 in ZyWAN firewall. This must be included explicitly in

Networking

for any Terminal Server port configured.

The next sections provide detailed descriptions including the Web configuration pages for each setting.

Summary of Contents for ZyWAN



































































































































Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands

Eurotech ZyWAN, User Manual

Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands