Eurotech ZyWAN User Manual Download Page 53

Page: 53 / 130

PART 2: SOFTWARE CONFIGURATION

110150-1001F

FIELD/OPTION

EXPLANATION

Operational Status Information

RX Level

Received cellular signal level (dBm)

PS State

State of packet-switch (data) connection to cellular network

Current Frequency Band

Frequency band currently in use

Current Network Technology

Network technology currently used by cellular module

Time

Current time, in seconds from power-up of the cellular module

Temperature

Approximate temperature, in degrees C

Mode

Current mode of the cellular module operation

System Mode

Current system mode acquired by cellular module

WCDMA Band / Channel

Current WCDMA band and channel number being accessed

GSM Band / Channel

Current GSM band and channel number being accessed

GMM State / Sub-state

Current GMM state

MM State / Sub-state

Current MM state

WCDMA L1 State

Current WCDMA L1 state, if in CDMA mode

RRC State

Current WCDMA RRC state, if in CDMA mode

Serving Cell

Serving cell, if in GSM/GPRS mode

GPRS State

Current GPRS state, if in GSM/GPRS mode

Click the

Network Information

link to show information about the 3G cellular network.

FIELD/OPTION

EXPLANATION

Network Information

Service Status

Service availability

(Service, No service, Limited service, Limited regional service)

Service Domain

Current service domain (circuit or packet switched, or both)

Roaming Status

Roaming status indicator

System Mode

Current system mode

(No service, GSM/GPRS mode, WCDMA mode)

SIM Status

Availability of SIM card

Available Network Technologies

Technologies available on current network

Summary of Contents for ZyWAN



































































































































Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands

Eurotech ZyWAN, User Manual

Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands