Eurotech ZyWAN User Manual Download Page 56

Page: 56 / 130

ZyWAN - User Manual

110150-1001F

Click the

Operational Status Information

link to show current operational details, such as the IDEN cellular

signal strength.

FIELD/OPTION

EXPLANATION

Operational Status Information

Signal Strength, RSSI

Received signal strength of IDEN signal, in dBm

CSQ

IDEN cellular signal quality indication (SQE, higher number is better)

Registration Status

Status whether the cellular module is registered on the cellular

network

GSM RSSI

Received signal strength of GSM carrier, 0-31 (31 is best)

Click the

Network Information

link to show information about the IDEN cellular network.

FIELD/OPTION

EXPLANATION

Network Information

Frequency

Current frequency (in Hz) and frequency band to which the iO270

cellular module is connected

Bandmap

Bandmap information being used by the iO270

Band Info

Primary and secondary bands in use in the iO270

WDS Channel

Channel number of wireless data system (WDS)

Primary DNS IP

Secondary DNS IP

Addresses of DNS server provided by the cellular network

Summary of Contents for ZyWAN



































































































































Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands

Eurotech ZyWAN, User Manual

Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands