Eurotech ZyWAN User Manual Download Page 14

Page: 14 / 130

ZyWAN - User Manual

110150-1001F

Chapter 1 Interfaces

The front panel of the ZyWAN contains the following ports and indicators:

Further information about these ports and connectors is provided in the following sections.

CELL – Cellular

antenna connection

(SMA)

COM2 – RS-232

for data

communication

GPS – Antenna connection

for GPS receiver (SMA)

COM3 – RS-232 or RS-422/485

for data communication

DIV – Diversity antenna,

optionally used for EVDO (SMA)

COM1 – RS-232 serial port

for local console diagnostics

LED indicators

USB ports (2) – One or both may be

used internally for EvDO, etc.

LAN ports (2) – RJ-45 10/100BaseT

Ethernet, with link and activity LEDs

802.11 – Antenna connection for

wireless WiFi network (reverse SMA)

POWER –

10-26 V DC input

Summary of Contents for ZyWAN



































































































































Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands

Eurotech ZyWAN, User Manual

Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands