Eurotech ZyWAN User Manual Download Page 101

Page: 101 / 130

PART 2: SOFTWARE CONFIGURATION

101

110150-1001F

The following screen capture shows the

Table of Terminal Servers

Note:

Any Terminal Server (TCP) ports configured here must also be included in the “Open

Ports” section of the

Networking

page, so the firewall will allow connections to be made

to the ZyWAN.

The following table lists the fields and options that are available and that must be set for each configured

Terminal Server configuration.

FIELD/OPTION

EXPLANATION

IP Port

Enter the IP port number (between 1 and 65535) to be used on

the ZyWAN for incoming TCP/IP connections from a network

client application. The IP address to which the client connects

may be any valid address configured for the ZyWAN on any

interface.

Time to Live

Enter the

Time To Live

for the connection (in seconds). This is

the maximum time of no activity from the network-connected

client, before the ZyWAN closes the Terminal Server

connection. The range for

Time To Live

is 1 to 65535 seconds.

(Setting the value to zero (0) will cause the Terminal Server to

never shut down upon no activity, which is not recommended.)

Summary of Contents for ZyWAN



































































































































Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands

Eurotech ZyWAN, User Manual

Search results

Summary of Contents for ZyWAN

Reviews:

Related manuals for ZyWAN

Brands by name

Popular brands