Epson S1C17001 Technical Manual Download Page 50

Page: 50 / 351

6 INITERRUPT CONTROLLER

S1C17001 TECHNICAL MANUAL

EPSON

0x4300: Interrupt Flag Register (ITC_IFLG)

Bit

Name

Function

Setting

Init. R/W

Remarks

Interrupt Flag
Register
(ITC_IFLG)

0x4300

(16 bits)

D15

IIFT7

C interrupt flag

1 Cause of

interrupt
occurred

0 Cause of

interrupt not
occurred

R/W Reset by writing 1.

D14

IIFT6

SPI interrupt flag

R/W

D13

IIFT5

Remote controller interrupt flag

R/W

D12

IIFT4

UART interrupt flag

R/W

D11

IIFT3

16-bit timer Ch.2 interrupt flag

R/W

D10

IIFT2

16-bit timer Ch.1 interrupt flag

R/W

IIFT1

16-bit timer Ch.0 interrupt flag

R/W

IIFT0

8-bit timer interrupt flag

R/W

EIFT7

PWM&capture timer interrupt flag 1 Cause of

interrupt
occurred

0 Cause of

interrupt not
occurred

R/W Reset by writing 1 in

pulse trigger mode.

Cannot be reset by
software in level trig-
ger mode.

EIFT6

reserved

R/W

EIFT5

reserved

R/W

EIFT4

8-bit OSC1 timer interrupt flag

R/W

EIFT3

Clock timer interrupt flag

R/W

EIFT2

Stopwatch timer interrupt flag

R/W

EIFT1

P1 port interrupt flag

R/W

EIFT0

P0 port interrupt flag

R/W

D[15:8]

IIFT[7:0]: Interrupt Flags (for Pulse Trigger)

These are interrupt flags indicating the interrupt factor occurrence status.

1(R):

Interrupt factor present

0(R):

No interrupt factor (default)

1(W):

Reset

flag

0(W):

Disabled

The interrupt flags are reset to 1 if an interrupt factor occurs in the peripheral modules.

An interrupt is generated to the S1C17 core provided the following conditions are met:

1. The corresponding interrupt enable bit is set to 1.

2. No other interrupt having requests higher priority levels have occurred.

3. The PSR IE bit was set to 1 (interrupt permitted).

4. The corresponding interrupt level setting bit has been set to a higher level than the S1C17 core inter-

rupt level (IL).

The interrupt flags are set to 1 when an interrupt factor occurs regardless of the interrupt enable bit or
interrupt level setting bit states.

The interrupt flags must be reset and the PSR must be reset (by setting the IE bit to 1 or with the

reti

command) to accept the next interrupt after interrupt occurrence.

An interrupt factor flag set to 1 is reset by writing 1.

Table 6.7.2: Hardware interrupt factors and interrupt flags

Interrupt flag

Hardware interrupt factor

IIFT0 (D8)

8-bit timer interrupt: Timer underflow

IIFT1 (D9)

16-bit timer Ch.0 interrupt: Timer underflow

IIFT2 (D10)

16-bit timer Ch.1 interrupt: Timer underflow

IIFT3 (D11)

16-bit timer Ch.2 interrupt: Timer underflow

IIFT4 (D12)

UART interrupt: Transmit buffer empty/Receive buffer full/Receive error

IIFT5 (D13)

Remote controller interrupt: Data length counter underflow/Input rise-up/Input drop-
off

IIFT6 (D14)

SPI interrupt: Transmit buffer empty/Receive buffer full

IIFT7 (D15)

C interrupt: Transmit buffer empty/Receive buffer full

Summary of Contents for S1C17001
































































































































































































































































































































































Search results

Summary of Contents for S1C17001

Reviews:

Related manuals for S1C17001

Brands by name

Popular brands

Epson S1C17001, Technical Manual

Search results

Summary of Contents for S1C17001

Reviews:

Related manuals for S1C17001

Brands by name

Popular brands