Epson S1C17001 Technical Manual Download Page 229 | Manualshive

Page: 229 / 351

background image

18 UART

220

EPSON

S1C17001 TECHNICAL MANUAL

Receive error interrupt

To use this interrupt, set REIEN (D6/UART_CTL register) to 1. If REIEN is set to 0 (default), interrupt re-
quests will not be sent to the ITC for this factor.

∗

REIEN

: Receive Error Interrupt Enable Bit in the UART Control (UART_CTL) Register (D6/0x4104)

The UART sets the error flags shown below to 1 if a parity error, framing error, or overrun error is detected
when receiving data. If receive error interrupts are permitted (REIEN = 1), an interrupt request pulse is output
at the same time to the ITC.

∗

PER

: Parity Error Flag in the UART Status (UART_ST) Register (D5/0x4100)

∗

FER

: Framing Error Flag in the UART Status (UART_ST) Register (D6/0x4100)

∗

OER

: Overrun Error Flag in the UART Status (UART_ST) Register (D4/0x4100)

If other interrupt conditions are satisfied, an interrupt occurs.

Inspect the error flags above as part of the UART interrupt processing routine to determine whether the UART
interrupt was caused by a receive error. If any of the error flags has the value 1, the interrupt processing routine
will proceed with error recovery.

UART interrupt ITC registers

The UART ITC control bits are listed below.

Interrupt flag

∗

IIFT4

: UART Interrupt Flag in the Interrupt Flag (ITC_IFLG) Register (D12/0x4300)

Interrupt enable bit

∗

IIEN4

: UART Interrupt Enable Bit in the Interrupt Enable (ITC_EN) Register (D12/0x4302)

Interrupt level setting bit

∗

IILV4[2:0]

: UART Interrupt Level Bits in the Internal Interrupt Level Setup (ITC_ILV2) Register 2

(D[2:0]/0x4312)

If an interrupt request pulse is output by the UART, the corresponding interrupt flag is set to 1.

If the interrupt enable bit corresponding to this interrupt flag is set to 1, the ITC sends an interrupt request to
the S1C17 core. To prohibit UART interrupts, set the interrupt enable bit to 0. The interrupt flag is set to 1 by a
UART interrupt request pulse, regardless of the interrupt enable bit setting (i.e., even if set to 0).

The interrupt level setting bit sets the UART interrupt level (0 to 7).

The S1C17 core accepts interrupts when all of the following conditions are met:
• The interrupt enable bit is set to 1.
• The PSR (S1C17 core internal processor status register) IE (interrupt enable) bit is set to 1.
• The UART interrupt has a higher interrupt level set than that set for the PSR IL (interrupt level).
• No other interrupt factors having higher precedence (e.g., NMI) are present.

For detailed information on these interrupt registers and operations when interrupts occur, refer to “6 Interrupt
Controller (ITC).”

Interrupt vectors

The UART interrupt vector numbers and vector addresses are as listed below.

Vector number: 16 (0x10)

Vector

address:

0x8040

«
...
227
228
229
230
231
...
»

Summary of Contents for S1C17001
































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C17001

Brand: Parasound Pages: 72

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: Calpeda Pages: 4

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

Brand: K1EL Pages: 46

CompactRIO cRIO-9002

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 145

Brand: National Instruments Pages: 42

Brand: National Instruments Pages: 8

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 17

Brand: YASKAWA Pages: 58

J1000 CIMR-JC series

Brand: YASKAWA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands