Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 61 | Manualshive

Page: 61 / 65

background image

Software Release: [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042;

BTL: 02.09.10015.00]

Section 40

61

00-02-0939

2019-06-13

MPC-10 Specifications

Interface

Display:

Monochrome HR-TFT, 2.7 in. / 68mm, WQVGA (400 x 240 pixels)
(3) LEDs

:

green (mode), yellow (warning) and red (shutdown)

Operator controls:

(11) Raised silicon keypads, tactile feedback

Power Supply

Operating Voltage: 8-32 VDC, reverse battery polarity and load-dump protected
Cranking Power Holdup: 0 VDC up to 50mS (also good for brownout/blackout instances)
Power Consumption:

18W max without two 1A High-side FETs active,
146W max with two 1A High-side FETs active

Inputs

(5) Digital, configurable (active on High, Low, Open)
(3) Analog, configurable (4-20mA, 0-5V, resistive or digital ground)
(1) Frequency, supporting:

Magnetic Pickup (30 Hz

– 10 kHz, 2.0 VAC – 120 VAC) &

Engine Alternator (30 Hz

– 10 kHz, 4.5 VRMS – 90 VRMS)

Outputs

(3) Relay, Form C (dry / volt-free), 10A
(2) Low-side FET (-DC), 1A
(2) High-side FET (+DC), 1A
(1) Dedicated Alternator Excitation, +DC, 1A

Communications

(1) CAN: J1939
(1) RS485: Modbus RTU
(1) USB: 2.0B (Supported for quick Programming)

Mating Connectors

12 Position, DT06-12SA PO12 (Gray)
12 Position, DT06-12SB-PO12 (Black)
12 Position, DT06-12SC-PO12 (Green)

Physical / Environmental

Enclosure Material: Polycarbonate / ABS
Dimensions (WxHxD): 9.59 x 7.34 x 5.20 in. (243.48 x 186.5 x 132.23 mm)
Weight: 4 lbs (1.8 kg)
IP Rating: IP69K & IP67 front and back, IP66 panel seal when used with accessory gasket
Operating & Storage Temperature: -40° to +85° C (-40° to +185° F)
Vibration: 7.86 Grms (5-2000 Hz), 3-axis random
Shock: ±50G, 3 axis
Emissions & Immunity: SAE J1113, 2014/30/EU & 2014/35/EU

«
...
59
60
61
62
63
...
»

Summary of Contents for Murphy PowerCore MPC-10


































































Reviews:

No comments

Related manuals for Murphy PowerCore MPC-10

Brand: Samson Pages: 48

Brand: Mako Networks Pages: 15

Brand: Ebyte Pages: 34

Brand: YASKAWA Pages: 61

COOPER POWER SERIES

Brand: Eaton Pages: 50

Brand: OMC Pages: 18

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

FrameSaver 9120

Brand: Paradyne Pages: 20

VeriSafe VS2-NET

Brand: Panduit Pages: 6

Brand: Vanderbilt Pages: 2

eTracer ET4415BND

Brand: Epsolar Pages: 44

Brand: Graco Pages: 166

Brand: Viva Pages: 9

Dual Motor Focus Controller

Brand: Pegasus Astro Pages: 16

Brand: FMS Pages: 108

Brand: FADAL Pages: 2

i-Kiosk 100 Plus

Brand: FingerTec Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands