Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 39

Page: 39 / 65

Software Release: [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042;

BTL: 02.09.10015.00]

Section 40

00-02-0939

2019-06-13

acknowledgement of the fault is

NOT

required to restart in Auto after shutdown occurs if

active shutdown is removed from controller)

Analog Inputs (1-3)

(Medium Security)

for each of the analog inputs, the ability to select the following

parameters exists:

Analog input 1 (Medium Security)

: Factory set to Function: Disabled

Analog Input 2 (Medium Security)

: Factory set to Function: Disabled

Analog Input 3 (Medium Security)

: Factory set to Function: Disabled

Function (Medium Security)

Disabled

4-20mA Suction Pressure

0-5V Suction Pressure

4-20mA Discharge Pressure

0-5V Discharge Pressure
4-20mA System Level
4-20mA Flow Rate

4-20mA Ambient Temp

0-5V Ambient Temp
4-20mA Gear Box Pressure
0-5V Gear Box Pressure
Datcon Oil Pressure
Murphy Oil Pressure

(ES2P-100)

VDO5 Bar Oil Pressure

VDO7 Bar Oil Pressure

Murphy Engine Temp

(ES2T-250/300)

Datcon Engine Temp

VDO Engine Temp

Murphy Fuel Level

(ES2F)

VDO Fuel Level

Datcon Fuel Level

Murphy Oil Temp

(ES2T-250/300)

Datcon Oil Temp

VDO Oil Temp
Murphy PMK-400 Pressure

(Gear Box Pressure, Murphy PMK-400 Sensor)

Analog.Digital1
4-20mA Remote Throttle:

(4mA = Min Engine Speed, 20mA = Max Engine Speed, Remote

Throttle Digital Input must be active to allow analog to work properly)

0.5-4.5V Remote Throttle:

(0.5V = Min Engine Speed, 4.5V = Max Engine Speed, Remote

Throttle Digital Input must be active to allow analog to work properly)

Model 12 Air Temp Sensor:

(Murphy 0-5V Model 12 preset Ambient Temp Sensor)

Sensor Setup (Medium Security)

(This menu only appears when a transducer [4-20mA or 0-5V] is

selected for an analog input.)

Ambient Temp

(0-5V) or (4-20mA)

Discharge Pressure

(0-5V) or (4-20mA)

Suction Pressure

(0-5V) or (4-20mA)

Flow Rate

(4-20mA)

System Level

(4-20mA)

Relay (1-3) and Digital (1-4) Outputs

(Medium Security)

these same parameters are used for both the

Relay and Digital Outputs.

Summary of Contents for Murphy PowerCore MPC-10


































































Search results

Summary of Contents for Murphy PowerCore MPC-10

Reviews:

Related manuals for Murphy PowerCore MPC-10

Brands by name

Popular brands

Enovation Controls Murphy PowerCore MPC-10, Operation Manual

Search results

Summary of Contents for Murphy PowerCore MPC-10

Reviews:

Related manuals for Murphy PowerCore MPC-10

Brands by name

Popular brands