manualshive.com logo in svg

Enovation Controls Murphy PowerCore MPC-10, Operation Manual

Share
Download
Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 28

Software Release:   [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042; 

BTL: 02.09.10015.00]

 

 

Section 40

 

28

 

00-02-0939

 

2019-06-13

 

 
 

Suction Pressure 

 
 

Percent Load at Current RPM 

 
 

Current Engine Temperature 

 

Battery Voltage 

 

Icon Troubleshooting 

The warnings and shutdowns internally generated by the controller will show an Internal Fault on the top 
of the screen when a fault is displayed.  Check all fluid levels and pressures.  Ensure the cooling system 
and engine are functioning properly. 
 
The warnings and shutdowns the ECU generates will also be accompanied by a cause for the error.  
Consult with the engine manufacturer regarding fault codes shown on the screen. 
 
If the fault states it is internal and everything checks out normal, consider checking the set points or the 
bypass timer(s) to ensure the ranges are within normal operating settings for the engine and application. 

Menu Glossary 

System (Low Security) 

Date/Time 

(Low Security)

:

  

allows the setting of the controller’s date and time. 

Units 

(Medium Security)

: 

allows the setting of the units of measurement for information presented on the 

display. 

Pressure  Units 

(Medium  Security)

:   

allows  the  selection  of  PSI,  kPa  or  BAR  for  pressure 

designation.  

Factory set to PSI. 

Temperature  Units 

(Medium  Security)

: 

  allows  the  selection  of  Fahrenheit  or  Celsius  for 

temperature designation.  

Factory set to Fahrenheit. 

Level  Units 

(Medium  Security)

:   

allows  the  selection  of  Feet  or  Meters  for  Level  designation.  

Factory set to Feet.

 

Flow Units 

(Medium Security)

: 

allows the selection of gal/min (US), gal/min (UK), lpm (Liters per 

Minute),  lps  (Liters  per  Second),  m3/h  (Meters  Cubed  per  Hour)  and  m3/s  (Meters  Cubed  per 
Second) for flow designation.  

Factory set to gal/min (US). 

Fuel Rate Units

 (Medium Security): allows the selection of gal/hr (US), gal/min (US), gal/hr (UK), 

gal/min (UK), lph (Liters per Hour), lpm (Liters per Minute), m3/h (Meters Cubed per Hour) for fuel 
rate designation. 

Factory set to gal/hr (US). 

Language 

(Medium  Security)

:   

select:  English,  French,  German,  Spanish,  and  Italian. 

Factory  set  to 

English.

 

Summary of Contents for Murphy PowerCore MPC-10


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands