manualshive.com logo in svg

Enovation Controls Murphy PowerCore MPC-10, Operation Manual

Share
Download
Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 50

Software Release:   [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042; 

BTL: 02.09.10015.00]

 

 

Section 40

 

50

 

00-02-0939

 

2019-06-13

 

Communication Mapping 

This section outlines the RS485 Modbus Register Map and CAN Parameter Map. 

MPC-10 & TEC-10 RS485 Modbus Registers 

NOTE: The registers labeled Read/Write will allow the operator to change values through the 
Modbus as a temporary modification. If power is cycled to the MPC-10 / TEC-10, the values 
changed via Modbus will revert back to the last value entered locally.  Writing a 1 to register 
40240 will allow saving register changes to controller. 

REGISTER # 

TYPE 

DESCRIPTION 

UNITS 

40001-40002 

Read Only 

Current Engine Hours (32 Bit) 

Hours 

40003 

Read Only 

Actual Engine Speed 

RPM 

40004 

Read Only 

System Voltage (12.5 will read 125) 

VDC 

40005 

Read Only 

Actual Engine Oil Pressure 

kPa 

40006 

Read Only 

Actual Engine Temperature 

Celsius 

40007 

Read Only 

Controller State (Active State: Numeral Indicated) 

Numerals 

0 = ECU Stabilize Delay  
1 = Engine Stopped  
2 = Controller in Standby 

 

3 = Prestart 1 Delay 
4 = Check Safe to Start  
5 = Prestart 2 Delay 
6 = Crank On 
7 = Crank Rest 
8 = False Start Check 
9 = Engine Warmup Delay 
10 = Line Fill 1 Delay 
11 = Line Fill 2 Delay 
12 = Running Loaded 
13 = Running Cooldown Delay 
14 = Energize to Stop Delay 
15 = Engine Spindown Delay 
16 = Wait to Start Delay 

40008 

Read Only 

Active Shutdown Status (Active Fault: Bit = 1, Inactive: Bit = 0) 

0   = Overspeed SD 

(0 or 1) 

1   = Underspeed SD                       

(0 or 1) 

2   = Overcrank SD                        

(0 or 1) 

3   = Low Oil Pressure SD                

(0 or 1) 

4   = High Engine Temp SD        

(0 or 1) 

5   = Low Fuel SD                            

(0 or 1) 

6   = Low Discharge Pressure SD   

(0 or 1) 

7   = High Discharge Pressure SD  

(0 or 1) 

8   = Speed Signal Lost SD  

(0 or 1) 

9   = Low Lube Level SD  

(0 or 1) 

10 = Fuel Leak SD  

(0 or 1) 

11 = Fuel Filter Restriction SD  

(0 or 1) 

12 = Reserved  

Reserved 

Summary of Contents for Murphy PowerCore MPC-10


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands