manualshive.com logo in svg

Enovation Controls Murphy PowerCore MPC-10, Operation Manual, Page: 5 / 65

Share
Download
Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 5

Software Release:   [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 

2.9.23042; BTL: 02.09.10015.00]

 

 

Section 40

 

5

 

00-02-0939

 

2019-06-13

 

 

Table of Contents 

Introduction ................................................................................................................................. 7

 

Murphy PowerCore 10 (MPC-10 / TEC-10)..................................................................7

 

User Interface ...............................................................................................................9

 

Accessing the Menu ................................................................................................................ 10

 

Main Menu ................................................................................................................................. 11

 

Auto Start/Stop Functions Defined........................................................................................ 16

 

Single Contact Start/Stop (commonly known as single float in pumping markets) ..... 16

 

Two Contact Maintained Start/Stop (commonly known as dual floats in pumping 
markets) ..................................................................................................................... 16

 

Pressure, Level and Temperature Transducer Start/Stop .......................................... 16

 

Local Start Key Start/Stop .......................................................................................... 16

 

Quick-Start Setup ..................................................................................................................... 17

 

Mechanical Engine Setup........................................................................................... 17

 

J1939 Electronic Engine Setup (Factory Default) ....................................................... 18

 

Setting to Auto Start on a Single Contact Input (Single Float) .................................... 18

 

Setting to Auto Start on Local Start Key ..................................................................... 19

 

Setting up to Auto Start/Stop for 2 Contact Inputs (Dual Floats) ................................ 19

 

Setting to Auto Start on Pressure ............................................................................... 19

 

Setting up to Auto Start on Level ................................................................................ 20

 

Setting to Auto Start on Clock .................................................................................... 20

 

Setting to Auto Start on Temperature ......................................................................... 20

 

Setting up to Stop the Engine from Utilizing the Countdown Timer ............................ 21

 

Screen Examples ..................................................................................................................... 21

 

Additional Screens ..................................................................................................... 22

 

ISO Icons ................................................................................................................... 25

 

Icon Troubleshooting .................................................................................................. 28

 

Menu Glossary ......................................................................................................................... 28

 

System (Low Security) ............................................................................................... 28

 

Engine Settings (Low Security) .................................................................................. 31

 

Summary of Contents for Murphy PowerCore MPC-10


































































Reviews:

No comments