manualshive.com logo in svg

Enovation Controls Murphy PowerCore MPC-10, Operation Manual

Share
Download
Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 15

Software Release:   [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042; 

BTL: 02.09.10015.00]

 

 

Section 40

 

15

 

00-02-0939

 

2019-06-13

 

 

Figure 6:  Main Menu page 3 

 

Start / Stop Timers 

The  Start/Stop  Timers  menu  provides  the  operator  the  ability  to  add  a  countdown  timer,  scheduled 
start/stop times, and an engine exercise timer. All Start/Stop timers only work when the controller is set to 
auto mode. The countdown timer allows for the operator to set a desired countdown time and walk away 
from the engine for a controlled shutdown when the timer expires. There are three Start/Stop Timers the 
operator can choose from within this menu that allows for the specific day and hour the controller will start 
and stop utilizing the internal clock.  Review Start/Stop Timers under Menu Glossary section of this manual 
for full list and definition of each setting. 
 

NOTE: 

Start / Stop timers work in conjunction with other Start / Stop types.  The Start / 

Stop times are independent of the other Auto Start methods. If the engine is already 
running from another Start / Stop type when a Start / Stop timer occurs, the Start / Stop 
timer is ignored.  Once the engine is started by the Start / Stop timer the Auto Stop 
method is ignored and will be stopped by the set Stop time. 

Communication  

The Communications menu allows the operator to choose the type of RS485 communications such as PVA 
Gauge, Modbus or Local Display. The menu also allows for the operator to choose CAN termination and 
enabling of the CAN Parameter Map.  Review Communication under the Menu Glossary section of this 
manual for a full list and definition of each setting. 
 

Passcodes 

The Passcodes menu is only available in the high security menu and allows the operator to see the three 
level of passcodes set in the controller. The passcodes are read only in this view. Passcodes are able to 
be changed from default passcode setting via PowerVision for Controllers configuration tool. 
 

Summary of Contents for Murphy PowerCore MPC-10


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands