manualshive.com logo in svg

Enovation Controls Murphy PowerCore MPC-10, Operation Manual

Share
Download
Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 6

Software Release:   [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 

2.9.23042; BTL: 02.09.10015.00]

 

 

Section 40

 

6

 

00-02-0939

 

2019-06-13

 

Advanced Engine Settings (Low Security) ................................................................. 32

 

Throttle Menu (Medium Security) ............................................................................... 36

 

Input / Output Menu ................................................................................................... 37

 

Application Configuration (Low Security) ................................................................... 40

 

Start / Stop Timers (Low Security) ............................................................................. 46

 

Communication (High Security) .................................................................................. 48

 

Passcodes (High Security) ......................................................................................... 49

 

Load Configuration (High Security) MPC-10 ONLY ................................................... 49

 

Communication Mapping ....................................................................................................... 50

 

This section outlines the RS485 Modbus Register Map and CAN Parameter Map. ....... 50

 

MPC-10 & TEC-10 RS485 Modbus Registers............................................................ 50

 

CAN Parameter Map .................................................................................................. 55

 

Supplementary Information ................................................................................................... 59

 

Passcodes.................................................................................................................. 59

 

PC Configuration Software ......................................................................................... 59

 

MPC-10 Specifications ............................................................................................................ 61

 

Interface ..................................................................................................................... 61

 

Power Supply ............................................................................................................. 61

 

Inputs ......................................................................................................................... 61

 

Outputs ...................................................................................................................... 61

 

Communications ........................................................................................................ 61

 

Mating Connectors ..................................................................................................... 61

 

Physical / Environmental ............................................................................................ 61

 

TEC-10 Specifications ............................................................................................................. 62

 

Interface ..................................................................................................................... 62

 

Power Supply ............................................................................................................. 62

 

Inputs ......................................................................................................................... 62

 

Outputs ...................................................................................................................... 62

 

Communications ........................................................................................................ 62

 

Mating Connectors ..................................................................................................... 62

 

Physical / Environmental ............................................................................................ 62

 

Summary of Contents for Murphy PowerCore MPC-10


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands