manualshive.com logo in svg

Enovation Controls Murphy PowerCore MPC-10, Operation Manual

Share
Download
Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 47

Software Release:   [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042; 

BTL: 02.09.10015.00]

 

 

Section 40

 

47

 

00-02-0939

 

2019-06-13

 

time  unmonitored  and  then  shut  itself  off  when  that  time  has  expired  or  when  a  local  key  stop  occurs.  
Format of HH:MM:SS. Maximum countdown time is 120 hours. 

Factory set to 00:00:00 

NOTE: 

 The countdown timer is only active when starting in Auto mode. This timer will not 

start counting when starting the engine in manual mode and switching to auto mode after 
the engine is running. 

Start / Stop Timer (1-3) 

(Low Security)

: 

each of the three timers contains the ability to select from the 

following parameters: 

 

Start Day

 

(Low Security)

:  Factory set to Off

 

 

 

Sunday 

 

 

Monday 

 

 

Tuesday 

 

 

Wednesday 

 

 

Thursday 

 

 

Friday 

 

 

Saturday 

 

 

Daily 

 

 

Off 

 

Start Time:  format of HH:MM:SS (Low Security): 

Factory set to 12.00.00 AM.

 

 

Stop Day

 

(Low Security)

:  Factory set to Off

 

 

 

Sunday 

 

 

Monday 

 

 

Tuesday 

 

 

Wednesday 

 

 

Thursday 

 

 

Friday 

 

 

Saturday 

 

 

Daily 

 

 

Off 

 

Stop Time:  format of HH:MM:SS (Low Security): 

Factory set to 12.00.00 AM.

 

Engine Exerciser

 (Medium Security)

: 

This feature allows the operator to set a voltage point for when the 

battery voltage drops below for a given period of time the controller will provide an auto start for a defined 
period of time to energize the battery using the engine alternator. 

NOTE: 

 The exerciser is only active when the controller is in Auto mode. If the exerciser 

starts the engine the exerciser is the only auto stop method to stop the engine. This holds 
true with all the Start/Stop Timers. 

Exercise Mode

 (Medium Security)

: 

Set point for the operator to enable the voltage exerciser of the 

engine. 

Factory set to Disabled 

Low Voltage Set Point 

(Medium Security)

: 

Voltage the operator sets for the battery voltage to drop 

below before an auto start will initiate to exercise the engine for recharging the battery. 

Factory set 

to 9.5V 

Low Voltage Time 

(Medium Security)

: 

Time the operator sets for the voltage to be below the low 

voltage set point before an auto start is initiated. 

Factory set to 10 minutes 

Summary of Contents for Murphy PowerCore MPC-10


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands