manualshive.com logo in svg

Enovation Controls Murphy PowerCore MPC-10, Operation Manual, Page: 22 / 65

Share
Download
Enovation Controls Murphy PowerCore MPC-10 Operation Manual Download Page 22

Software Release:   [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042; 

BTL: 02.09.10015.00]

 

 

Section 40

 

22

 

00-02-0939

 

2019-06-13

 

Additional Screens  

 

Figure 9:  Main Screen 

 

This is the main screen, and it displays actual and target RPM, Mode of Operation, Timer progress, % Soot 
Level, % DEF Level and current State, along with icons and warnings. 
 

 

Figure 10:  First 4-Up Screen 

 
This is the first 4 up screen, displaying engine RPM, oil pressure, engine temperature and battery voltage. If 
alternate parameters are desired, these may be changed using the free MPC-10 / TEC-10 software 
configuration tool.  
 

 

Figure 11:  Second 4-Up Screen 

 
This is the second 4 up screen, displaying engine RPM, engine temperature, fuel level and GPH. If 
alternate parameters are desired, these may be changed using the free MPC-10 / TEC-10 software 
configuration tool.  
 

 

Summary of Contents for Murphy PowerCore MPC-10


































































Reviews:

No comments