Endress+Hauser Solimotion FTR20 Operating Instructions Manual Download Page 17

Page: 17 / 60

Solimotion FTR20

Electrical connection

Hauser

Electrical connection

6�1

Connection requirements

Please note the following points before connecting up the device:

• The voltage supply must match the voltage specified on the nameplate.

• Switch off the supply voltage before connecting the device.

• Connect a potential matching line to the terminal to be used on the FTR20 before

connecting the device to the power supply.

• When connecting to the public power supply, a power switch for the device must be installed

within easy reach of the device. The switch is to be identified as a disconnecting device for

the device (EN/IEC 61010).

• The cable glands and connectors are permitted for connecting fixed cables and lines only.

The operator must ensure adequate strain relief.

• The device is to be attached so that the cable gland is protected from mechanical damage

(degree of mechanical hazard "low" – impact energy: 4 joules).

• Unused guide openings must be sealed off using sealing plugs, the plastic transport sealing

plug does not meet this requirement and must therefore be replaced during installation.

For devices intended for use in hazardous areas, please read the information and comply

with the instructions in the Ex documentation (XA).

6�1�1

Required tools

Connection

Tool

Terminals and screwed contact of the optional M12 plug connector, Binder

series 713/763

0.6 x 3.5 mm

Potential equalization

PZ2

Cable glands (F16 plastic housing)

SW25

Cable glands (F15 stainless steel housing, F34 aluminium housing and

optional Harting HAN8D plug connector)

SW22

Cable gland (optional M12 plug connector, Binder series 713/763)

SW13

Crimp contacts optional Harting HAN8D plug connector

Suitable crimping tool

6�1�2

Connecting cable requirements

The connecting cables provided by the customer must fulfil the following requirements:

• Electrical safety in accordance with applicable national regulations.

• Permitted temperature range → 55

• Normal installation cable with at least three wires

• Cable cross-sections: 0.2 to 2.5 mm

or AWG 24 to 12

• The terminals are only approved for connecting fixed cables. The operator must provide

suitable strain relief.

Summary of Contents for Solimotion FTR20





























































Search results

Summary of Contents for Solimotion FTR20

Reviews:

Related manuals for Solimotion FTR20

Brands by name

Popular brands

Endress+Hauser Solimotion FTR20, Operating Instructions Manual

Search results

Summary of Contents for Solimotion FTR20

Reviews:

Related manuals for Solimotion FTR20

Brands by name

Popular brands