Endress+Hauser Solimotion FTR20 Operating Instructions Manual Download Page 6

Page: 6 / 60

Solimotion FTR20

About this document

Hauser

1�2�5

Device-specific symbols

LED on

Indicates an illuminated LED

LED off

Indicates a non-illuminated LED

Configuration mode

Indicates the function number or value

Normal operation

Indicates only the signal strength of the bulk solids movement

Key (+)

Indicates the key for increasing a function value

Key (-)

Indicates the key for reducing a function value

Minimum bulk flow

Indicates a minimum or absent bulk flow

Maximum bulk flow

Indicates a maximum bulk flow

1�2�6

Symbols in graphics

A, B, C ��

View

1, 2, 3 ... Item number

Hazardous area

Safe area (non-hazardous area)

1�3

Documentation

The document types listed are available:

In the Download area of the Hauser website: www.endress.com → Downloads

1�3�1

Standard documentation

Document

Purpose and content of the document

Technical information

TI00447F/97/EN

Planning aid for your device

This document contains all the technical specifications for the

device and provides an overview of all the items that can be

ordered for use in conjunction with or as part of the device.

Summary of Contents for Solimotion FTR20





























































Search results

Summary of Contents for Solimotion FTR20

Reviews:

Related manuals for Solimotion FTR20

Brands by name

Popular brands

Endress+Hauser Solimotion FTR20, Operating Instructions Manual

Search results

Summary of Contents for Solimotion FTR20

Reviews:

Related manuals for Solimotion FTR20

Brands by name

Popular brands