manualshive.com logo in svg

Endress+Hauser Solimotion FTR20, Operating Instructions Manual

Share
Download
Endress+Hauser Solimotion FTR20 Operating Instructions Manual Download Page 14

Solimotion FTR20

Installation

14

Hauser

1

 

2

3

 

 

 

 4

 

 

 

5

6

 

α

 = 45 

°

4 

Installation position for material detection on conveyor belt

• Choose a location to install the device where application-specific influences will be minimal.

•  With vibrating mounting locations it is recommended to use devices with encapsulated 

electronics (see ordering structure "Accessory mounted").

 

   For devices intended for use in hazardous areas, please read the information and comply 

with the instructions in the Ex documentation (XA).

5�2 

Installing the FTR20

5�2�1 

Direct mounting with threaded connection

The simplest mounting method is by screwing into the process wall. To do this, a 

corresponding internal thread (Rp 1½, 1½ NPT or G 1½) must be available in the process.

5�2�1�1  Installation with self-sealing connection thread (R 1½ and 1½ NPT)

5 

Installation with self-sealing connection thread

Summary of Contents for Solimotion FTR20





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands