Emerson Rosemount 8800D Series Reference Manual Download Page 66 | Manualshive

Page: 66 / 192

background image

56

Reference Manual

00809-0100-4772, Rev FA

Transducer Block

March 2016

Transducer Block

4.2.5

Error conditions

4.3

Flow units

The flow units are configured in the AI block. If Standard or Normal flow units are selected,
the density ratio must be entered in the transducer block in order for the conversion to take
place. If mass units are selected, the process density must be entered.

4.3.1

Standard/normal flow units

The flowmeter allows you to measure standard or normal flow units (SCFM, SCFH, NCMM,
NCMH, NCMD). Configure the software in one of two ways:

1.

Enter the density ratio to convert from actual flow rate to standard flow rate.

2.

Enter the process and base conditions. (The flowmeter electronics will then
calculate the density ratio for you.)

See Density Ratio and Process and Base Conditions below for definitions.

Note

Be careful to calculate and enter the correct conversion factor. Standard flow is calculated
with the conversion factor you enter. Any error in the factor entered will result in an error in
the standard flow measurement. If pressure and temperature change over time, use actual
volumetric flow units. The flowmeter does not compensate for changing temperature and
pressure.

Symptom

Possible
causes

Corrective action

Mode will not leave out of

service (OOS)

Target mode

not set

Set target mode to something other than OOS.

Resource block

The actual mode of the resource block is OOS.

See

for corrective action.

PV or SV is BAD.

Measurement

See

4.2.2: Diagnostics

Flow is above SENSOR_RANGE.EU100.

PV or SV is UNCERTAIN.

Measurement

Flow is above PRIMARY_VALUE_RANGE.EU100

or flow is being simulated in the transducer

block.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
64
65
66
67
68
...
»

Summary of Contents for Rosemount 8800D Series

































































































































































































Reviews:

No comments

Related manuals for Rosemount 8800D Series

Brand: QLA Pages: 18

Brand: E-Mon Pages: 72

Brand: Rhosonics Pages: 65

Brand: Bahco Pages: 21

Brand: Kübler Pages: 72

Brand: Kingfisher Pages: 52

Brand: MULTISPAN Pages: 4

Brand: NIEUWKOOP Pages: 2

Brand: wattwatchers Pages: 14

Brand: X-Rite Pages: 54

Brand: 365SMART Pages: 20

Brand: Eddyfi Technologies Pages: 72

Brand: MFJ Pages: 9

Brand: Ress Pages: 11

Brand: National Instruments Pages: 40

Brand: Hioki Pages: 16

Brand: Tusa Pages: 137

Brand: Compact Instruments Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands