manualshive.com logo in svg

Emerson Rosemount 8800D Series, Reference Manual

The Emerson Rosemount 8800D Series is a leading-edge flow meter system. It offers unparalleled accuracy and reliable performance. To unlock the full potential of this exceptional product, make sure to download the comprehensive and free Reference Manual from manualshive.com. This manual will serve as your ultimate guide to harnessing all the benefits of the 8800D Series.

Share
Download
background image

43

Reference Manual 

00809-0100-4772, Rev FA

Transducer Block

March 2016

Transducer Block

Section 4

Transducer Block

Overview   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  page 35
Parameters and descriptions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  page 37
Flow units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  page 45
Transducer block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  page 46

4.1

Overview

This section contains information on the flowmeter transducer block. Descriptions of all 
transducer block parameters, errors, and diagnostics are listed. Also, the modes, alarm 
detection, status handling, application information, and troubleshooting are discussed.

Figure 4-1. Transducer Block Diagram

4.1.1

Quick transducer block configuration guide

Proper configuration of the flowmeter is essential for accurate performance. The following 
is a quick configuration guide for those already familiar with vortex meters, especially the 
Rosemount

™

 8800D Vortex Flowmeter.

For most parameters configured in the flowmeter, the transmitter must perform extensive 
calculations to derive internal parameters used to accurately measure flow. It is 
recommended that each parameter in the Transducer Block be configured and sent to the 
transmitter individually. If too many parameter changes are sent to the transmitter at one 
time, the transmitter will return an error. The parameters not accepted will have to be 
re-sent.

Configuration order

The Transducer Block parameters can be configured in any order, but the following is a 
recommended procedure and can also be used as a checklist for configuration items.

A/D Signal 

Conversion

Diagnostics

Da

m

p

in

g

Un

its

/R

an

g

in

g

1

Flow

TB

Channel

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Reviews:

No comments

Related manuals for Rosemount 8800D Series

Keithley 2002 Repair Manual preview
2002
Brand: Keithley Pages: 148
M-system 47LV Operating Manual preview
47LV
Brand: M-system Pages: 18
Icon Process Controls Level Pro UltraPro 500 Series Instruction Manual preview
Level Pro UltraPro 500 Series
Brand: Icon Process Controls Pages: 19
Fluke Comark Diligence 600 Reference Manual preview
Comark Diligence 600
Brand: Fluke Pages: 61
Thermo Scientific Orion Versa Star Pro Series Instruction Sheet preview
Orion Versa Star Pro Series
Brand: Thermo Scientific Pages: 4
Fly Henry Fly Meter Manual preview
Fly Meter
Brand: Fly Henry Pages: 5
Circutor Wibeee Max Instruction Manual preview
Wibeee Max
Brand: Circutor Pages: 48
Elcontrol Vip 396 485 Addition To The User Manual preview
Vip 396 485
Brand: Elcontrol Pages: 7
Fluke FI-500 FiberInspector Micro Quick Start Manual preview
FI-500 FiberInspector Micro
Brand: Fluke Pages: 2
S+S Regeltechnik AERASGARD FSFTM-CO2-Modbus Series Operating Instructions, Mounting & Installation preview
AERASGARD FSFTM-CO2-Modbus Series
Brand: S+S Regeltechnik Pages: 32
International Light Technologies ILT2400 Operation Manual preview
ILT2400
Brand: International Light Technologies Pages: 19
Campbell CMP6-L Instruction Manual preview
CMP6-L
Brand: Campbell Pages: 42
Purafil ONGuard 4000 Quick Start Manual preview
ONGuard 4000
Brand: Purafil Pages: 2
Raycus A6000D User Manual preview
A6000D
Brand: Raycus Pages: 86
Environmental Express 35643-00 Instruction Manual preview
35643-00
Brand: Environmental Express Pages: 17
NI PXIe-4141 Calibration Procedure preview
PXIe-4141
Brand: NI Pages: 20
LaMotte DO Tracer Meter Manual preview
DO Tracer Meter
Brand: LaMotte Pages: 21
SYSMEX CyFlow Space Operating Manual preview
CyFlow Space
Brand: SYSMEX Pages: 46

Brands by name

Popular brands

Load more brands