Emerson Rosemount 8800D Series Reference Manual Download Page 173

Page: 173 / 192

Alerts

March 2016

Reference Manual

00809-0100-4772, Rev FA

163

Alerts

Figure D-2. NE 107 Status Signal to PlantWeb Alert Mapping

The alert priority enumeration value

Alerts have priorities that determine if they occur, and where and how they are
annunciated.

NE107 status signals and PlantWeb alerts use the same priorities and annunciate the same
ways.

0 = Alerts will not occur. If there is an existing alert and the priority is changed from a

number greater than zero to zero, it will clear. Active device diagnostics are still shown
within the Device Description even if the alert has been cleared.

1 = The associated alert is not sent as a notification. If the priority is above 1, then the alert

must be reported.

2 = Reserved for alerts that do not require the attention of a plant operator, e.g. diagnostic

and system alerts. Block alert, error alert, and update event have a fixed priority of 2.

3-7 = Increasing higher priorities - advisory alerts.

8-15 = Increasing higher priority - critical alerts.

PlantWeb Alert priorities are configured using DeltaV.

OFFSPEC

ADVISE

FAILED

CHECK

FAIL

MAINT

NE 107 Status Signal

PlantWeb Alert

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Emerson Rosemount 8800D Series, Reference Manual, Page: 173 / 192

Search results

Summary of Contents for Rosemount 8800D Series

Reviews: