Emerson Rosemount 8800D Series Reference Manual Download Page 96

Page: 96 / 192

Reference Manual

00809-0100-4772, Rev FA

Troubleshooting

March 2016

Troubleshooting

Table 7-2. Transducer Block Status Definitions (TB_ELECTRONICS_STATUS)

Value

Name and description

LCD display
indication
(if any)

Corrective actions

0x00000002

SW_DETECTED_ERR: The device software has detected

a software (typically math) error.

FAULT SFTWR

Restart the transmitter.

(1)

0x00000004

COPROCESSOR_ERR: The coprocessor has detected a

math or instruction error.

FAULT COPRO

Restart the transmitter.

(1)

0x00000010

INTERRUPT_ERROR: The transducer block has detected

that the coprocessor ASIC has stopped generating flow

data interrupts.

FAULT ASIC

Restart the transmitter.

(1)

0x00000020

COPROC_RAM_ERR: The coprocessor has detected a

RAM error at startup.

FAULT RAM

Restart the transmitter.

(1)

0x00000040

COPROC_ROM_ERR: The coprocessor has detected a

ROM error at startup.

FAULT ROM

Restart the transmitter.

(1)

0x00000100

TRIGGER_OVERRANGE: The transducer has detected

that the configuration for the filter trigger level is out of

range.

Verify the filter trigger

level configuration.

Default value is 4.

0x00000200

LOW_PASS_OVERRANGE: The transducer has detected

that the configuration for the low pass filter is out of

range.

Verify the low-pass filter

configuration.

0x00000400

LOW_FLOW_CUT_OVERRANGE: The transducer has

detected that the configuration for the low-flow cutoff

is out of range.

Verify the low-flow cutoff

configuration. Optimize

filters.

0x00000800

SD2_COMM_ERR: There has been a communications

error detected in on-board messaging.

FAULT SDCOM

Restart the transmitter.

(1)

0x00001000

SD2_RESET: An ASIC on the sensor board has reset.

FAULT SDPLS

Voltage at the transmitter

terminals should be

greater than or equal to 9

VDC. Restart the

transmitter.

(1)

0x00002000

SENSOR_PWR_FAIL: The sensor board power has failed.

FAULT SPOWR

Voltage at the transmitter

terminals should be

greater than or equal to 9

VDC.

0x00004000

TC_OPEN: An open circuit has been detected on the

thermocouple used to measure the process

temperature.

FAULT TC

Check the thermocouple

connection to the

transmitter housing.

Replace the

thermocouple.

0x00008000

COPR_COEFF_BAD: The thermocouple math

coefficients used to calculate process temperature are

corrupt or invalid.

FAULT COEFF

Replace the transmitter.

0x00100000

AMBIENT_TEMP_ALARM: The temperature of the

transmitter electronics is beyond operating limits.

FAULT TEMP

Change the ambient

temperature around the

transmitter housing.

Remount the transmitter

in a different orientation

or consider a remote

mount transmitter.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Related manuals for Rosemount 8800D Series

Brands by name

Popular brands

Emerson Rosemount 8800D Series, Reference Manual

Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Related manuals for Rosemount 8800D Series

Brands by name

Popular brands