Emerson Rosemount 8800D Series Reference Manual Download Page 101

Page: 101 / 192

Reference Manual

00809-0100-4772, Rev FA

Troubleshooting

March 2016

Troubleshooting

Removing the terminal block

Turn off the electric power to the flowmeter.

Unscrew the cover.

Figure 7-6. F

OUNDATION

Fieldbus Terminal Block Assembly

A. Cover
B. O-ring
C. Terminal block
D. Captive screws (3)

Disconnect the wires from the field terminals. Be sure to secure them out of the
way.

Loosen the captive screws.

Pull outward on the block to remove it from the housing.

Installing the terminal block

Align the terminal block over the captive screw holes in the terminal block side of
the electronics housing.

Slowly press the terminal block into place. Do not force the block into the housing.
Check the screw alignment if it does not glide into place.

Tighten the three captive screws to anchor the terminal block.

Connect the wires to the appropriate field terminals.

If you have the transient option (Option T1), reinstall the tighten the transient
ground screw.

Screw on and tighten the cover.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Related manuals for Rosemount 8800D Series

Brands by name

Popular brands

Emerson Rosemount 8800D Series, Reference Manual

Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Related manuals for Rosemount 8800D Series

Brands by name

Popular brands