manualshive.com logo in svg

Emerson Rosemount 8800D Series, Reference Manual, Page: 38 / 192

Share
Download
Emerson Rosemount 8800D Series Reference Manual Download Page 38

28

Reference Manual

00809-0100-4772, Rev FA

Installation

March 2016

Installation

Note

In some applications it may be necessary to install conduit seals and arrange for conduits to 
drain to prevent moisture from entering the wiring compartment. Should not be removed 
when circuit live or in explosive atmosphere.

3.4.8

High-point installation

Prevent condensation in any conduit from flowing into the housing by mounting the 
flowmeter at a high point in the conduit run. If the flowmeter is mounted at a low point in 
the conduit run, the terminal compartment could fill with fluid. 

If the conduit originates above the flowmeter, route conduit below the flowmeter before 
entry. In some cases a drain seal may need to be installed.

Figure 3-10. Proper Conduit Installation with the Flowmeter

A. Conduit line

Note

In some applications it may be necessary to install conduit seals and arrange for conduits to 
drain to prevent moisture from entering the wiring compartment. These should not be 
removed when the circuit is live or in explosive atmosphere.

3.5

Hazardous locations

The flowmeter has an explosion-proof housing and circuitry suitable for intrinsically safe 
and non-incendive operation. Individual transmitters are clearly marked with a tag 
indicating the certifications they carry. To maintain certified ratings for installed 
transmitters, install in accordance with all applicable installation codes and approval 
drawings. For specific approval categories, refer to 

Appendix B: Product Certifications

.

A

A

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Reviews:

No comments