manualshive.com logo in svg

Emerson Rosemount 8800D Series, Reference Manual, Page: 104 / 192

Share
Download
Emerson Rosemount 8800D Series Reference Manual Download Page 104

94

Reference Manual

00809-0100-4772, Rev FA

Troubleshooting

March 2016

Troubleshooting

Figure 7-8. Loosening the Housing Rotation Screws

A. Housing rotation screws
B. Support tube

4.

Slowly pull the electronics housing no more than 1.5 in. from the top of the 
support tube. See 

Figure 7-9

.

Note

When the housing sensor header and sensor cable nut are connected, do not pull the 
housing more than 1.5 in. (40 mm) from the top of the support tube. Damage to the sensor 
cable may occur if the sensor cable is stressed.

Figure 7-9. Removing Electronics Housing

A. Sensor cable nut—SMA connector
B. Housing sensor header
C. 1.5 in. maximum (40mm) while sensor cable is connected to the sensor header

A

B

A

B

C

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Reviews:

No comments