manualshive.com logo in svg

Emerson Rosemount 8800D Series, Reference Manual, Page: 28 / 192

Share
Download
Emerson Rosemount 8800D Series Reference Manual Download Page 28

18

Reference Manual

00809-0100-4772, Rev FA

Configuration and Operation

March 2016

Configuration and Operation

Uncertain if man mode

Set the output status of the Analog Input block to uncertain if the actual mode of the block 
is Man.

Note

The instrument must be in Out of Service mode to set the status option.

2.8.6

Advanced features

The AI Function Block provides added capability through the addition of the following 
parameters:

ALARM_TYPE 

ALARM_TYPE allows one or more of the process alarm conditions detected by the AI 
function block to be used in setting its OUT_D parameter.

OUT_D

OUT_D is the discrete output of the AI function block based on the detection of process 
alarm condition(s). This parameter may be linked to other function blocks that require a 
discrete input based on the detected alarm condition.

2.9

Flow simulation

The electronics is capable of internally generating a flow signal that may be used to simulate 
a sensor signal. The simulated signal amplitude is based on the transmitter required 
minimum process density. The simulated signal can be a constant frequency or the 
simulated signal can be a varying frequency to represent a ramping flow rate.

Simulating the flow signal requires the simulate ENABLE jumper on the transmitter 
electronics board to be in the ‘ON’ position. The transmitters are shipped with the jumper 
in the ‘OFF’ position.

2.9.1

Using transducer block parameters

SIMULATION_CONTROL

Sim Disabled—Normal operation, no simulated flow signal.

Sim—Internal Generator—The internal frequency generator will produce the frequency 
signal.

Sim—External Generator—An External Frequency generator can be connected to Freq In and    
Ground connections on the electronics board.

SIMULATION_UNITS

PV Engineering Units—Simulated flow will be in engineering units.

PV Percent of Range—Simulated flow will be in percentage of Primary Value flow range.

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Reviews:

No comments