Emerson Rosemount 8800D Series Reference Manual Download Page 57

Page: 57 / 192

Reference Manual

00809-0100-4772, Rev FA

Transducer Block

March 2016

Transducer Block

ELEC_TEMP_RANGE

108

This parameter reports the measurement range of the electronics

temperature sensor (MTA model).

Upper sensor range = 90 °C

Lower sensor range = -55 °C

ELECTRON_TEMP

107

In an MTA model transmitter the electronics temperature is available.

This parameter will report the current temperature of the electronics in

engineering units configured in ELECTRON_TEMP_UNITS

ELECTRON_TEMP_UNITS

In an MTA model transmitter the electronics temperature is available.

This parameter is used to configure the engineering units of the

electronics temperature.

ELECTRONICS_STATUS

This parameter represents the transducer block electronics status. See

4.2.2: Diagnostics

FACTORY_INFO_FLOAT

For factory use only.

FACTORY_INFO_INDEX

For factory use only.

FACTORY_INFO_U16

For factory use only.

FACTORY_INFO_U32

For factory use only.

FACTORY_INFO_U8

For factory use only.

FILTER_AUTO_ADJUST

LOW_PASS_CODE

Selecting a fluid density close to the process density will adjust the

Trigger Level, Low Flow Cutoff, and Low Pass Filter to values that will work

well for most applications.

FILTER_RESTORE

This parameter will restore the Low Flow Cutoff, Low Pass Filter, and

Trigger Level to default configurations base on the mass of air for gas

process fluids or the mass of water for liquid process fluids.

1 = Normal state, 2 = Restore filters to defaults.

FIXED_PROC_DENSITY

The configured density of the process fluid is used to calculate flow when

mass units are selected.

FIXED_PROC_DENSITY_UNITS

The engineering units of PROCESS_DENSITY:

1097 = kilograms per cubic meter

1107 = pounds per cubic foot

FIXED_PROC_TEMP_UNITS

The engineering units of process temperature:

1001 = °C

1002 = °F

FIXED_PROC_TEMPERATURE

Process temperature is the configured temperature of the process fluid,

in units of °C or °F. This parameter is used to compensate the K-factor for

meter body expansion due to temperature. It is also used to calculate the

PROCESS_DENSITY_RATIO.

FLANGE_TYPE

Flange type specifies the wafer or the flange construction material (i.e.

ASME 150, ASME 300, ASME 600, PN64, JIS 10K, etc.). Flange type is

used as an input to the compensated K-factor calculation.

INSTALLATION_EFFECTS

An adjustment to the Compensated K-Factor to account for less than

ideal upstream piping effects.

K_FACTOR

The K-factor is the meter body calibration number. Units are reflected in

K_FACTOR_UNITS.

K_FACTOR_UNITS

K-factor units are the engineering units to be applied to the K_FACTOR

and COMPD_K_FACTOR.

0 = Pulses per gallon

LFC_IN_ENG_UNITS

This read-only parameter will indicate Low Flow Cutoff in currently

configured engineering units.

Table 4-1. Transducer Block Parameters

Parameter

Index

number

Definition

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Emerson Rosemount 8800D Series, Reference Manual, Page: 57 / 192

Search results

Summary of Contents for Rosemount 8800D Series

Reviews: