manualshive.com logo in svg

Emerson Rosemount 8800D Series, Reference Manual, Page: 21 / 192

Share
Download
Emerson Rosemount 8800D Series Reference Manual Download Page 21

11

Reference Manual 

00809-0100-4772, Rev FA

Configuration and Operation

March 2016

Configuration and Operation

MAINT_ALARMS

A maintenance alarm indicates the device or some part of the device needs maintenance 
soon. If the condition is ignored, the device will eventually fail. There are five parameters 
associated with MAINT_ALARMS, they are described below.

MAINT_ENABLED

The MAINT_ENABLED parameter contains a list of conditions indicating the device or some 
part of the device needs maintenance soon. If the condition is ignored, the device will 
eventually fail.

Below is a list of the conditions with the highest priority first.

1.

Low pass filter over range

2.

Low-flow cutoff over range

3.

Density calc using fixed temp (MTA only)

4.

Trigger over range

5.

Electronics temp beyond limit (MTA only)

MAINT_MASK

The MAINT_MASK parameter will mask any of the failed conditions listed in 
MAINT_ENABLED. A bit on means that the condition is masked out from alarming and will 
not be reported.

MAINT_PRI

MAINT_PRI designates the alarming priority of the MAINT_ALM, 

“Process alarms” on 

page 17

. The default is 0 and the recommended values is 3 to 7.

MAINT_ACTIVE

The MAINT_ACTIVE parameter displays which of the alarms is active. Only the condition 
with the highest priority will be displayed. This priority is not the same as the MAINT_PRI 
parameter described above. This priority is hard coded within the device and is not user 
configurable.

MAINT_ALM

An alarm indicating the device needs maintenance soon. If the condition is ignored, the 
device will eventually fail.

Advisory alarms

An advisory alarm indicates informative conditions that do not have a direct impact on the 
device's primary functions There are five parameters associated with ADVISE_ALARMS.

ADVISE_ENABLED

The ADVISE_ENABLED parameter contains a list of informative conditions that do not have a 
direct impact on the device's primary functions. Below is a list of the advisories with the 
highest priority first.

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Reviews:

No comments