Emerson Rosemount 8800D Series Reference Manual Download Page 80

Page: 80 / 192

Reference Manual

00809-0100-4772, Rev FA

Resource Block

March 2016

Resource Block

PD_TAG

PD tag description of device.

RECOMMENDED_ACTION

Enumerated list of recommended actions displayed with a device alert.

RESTART

RESTART allows a manual restart to be initiated. Several degrees of restart are

possible:

1 Run: Nominal state when not restarting

2 Restart resource: Not used

3 Restart with defaults: Set parameters to default values (see

START_WITH_DEFAULTS below for which parameters are set).

4 Restart processor: Does a warm start of CPU

RS_STATE

RS_STATE represents the state of the function block application state

machine.

SAVE_CONFIG_BLOCKS

FD_MAINT_ALARM

This parameter represents the number of EEPROM blocks that have been

modified since the last burn. This value will count down to zero when the

configuration is saved.

SET_FSTATE

Allows the FAULT_STATE condition to be manually initiated by selecting Set.

SHED_RCAS

SHED_RCAS represents the time duration at which to give up on computer

writes to function block RCas locations.

SHED_ROUT

SHED_ROUT represents the time duration at which to give up on computer

writes to function block ROut locations.

SOFTWARE_REV

Manufacturer software revision.

ST_REV

ST_REV is the revision level of the static data associated with the function

block. The revision value will be incremented each time a static parameter

value in the block is changed.

STRATEGY

The strategy field can be used to identify grouping of blocks. These data are

not checked or processed by the block.

TAG_DESC

TAG_DESC is the user description of the intended application of the block.

TEST_RW

TEST_RW is a parameter for a host to use to test reading and writing (not used

by the device at all).

UPDATE_EVT

This alert is generated by any change to the static data.

WRITE_ALM

This alert is generated if the write lock parameter is cleared.

WRITE_LOCK

If set, no writes from anywhere are allowed, except to clear WRITE_LOCK.

Block inputs will continue to be updated.

WRITE_PRI

This parameter specifies the priority of the alarm generated by clearing the

write lock.

Table 5-1. Resource Block Parameters

Parameter

Index

number

Description

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Related manuals for Rosemount 8800D Series

Brands by name

Popular brands

Emerson Rosemount 8800D Series, Reference Manual

Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Related manuals for Rosemount 8800D Series

Brands by name

Popular brands