Emerson Rosemount 8800D Series Reference Manual Download Page 82

Page: 82 / 192

Reference Manual

00809-0100-4772, Rev FA

Resource Block

March 2016

Resource Block

5.2.3

Alarm detection

A block alarm will be generated whenever the BLOCK_ERR has an error bit set. The types of
block error for the resource block are defined above (see

Table 5-2

A write alarm is generated whenever the WRITE_LOCK parameter is cleared. The priority of
the write alarm is set in the following parameter:



WRITE_PRI

Alarms are grouped into five levels of priority as shown in

Table 5-3

5.2.4

Status handling

There are no status parameters associated with the resource block.

5.2.5

VCR

The number of configurable VCRs is 19. The parameter is not contained or viewable within
the resource block, but it does apply to all blocks.

5.2.6

Troubleshooting

Refer to

Table 5-4

to troubleshoot any problems that you encounter.

Table 5-3. Alarm Priority

Priority

number

Priority description

The priority of an alarm condition changes to 0 after the condition that caused the

alarm is corrected.

An alarm condition with a priority of 1 is recognized by the system, but is not

reported to the operator.

An alarm condition with a priority of 2 is reported to the operator, but does not

require operator attention (such as diagnostics and system alerts).

3–7

Alarm conditions of priority 3 to 7 are advisory alarms of increasing priority.

8–15

Alarm conditions of priority 8 to 15 are critical alarms of increasing priority.

Table 5-4. Troubleshooting

Symptom

Possible causes

Corrective action

Mode will not

leave OOS.

Target mode not set

Set target mode to something other than OOS.

Memory failure

BLOCK_ERR will show the lost NV Data or Lost

Static Data bit set. Restart the device by setting

RESTART to processor. If the block error does not

clear, call the factory.

Block alarms

will not work.

Features

FEATURES_SEL does not have Alerts enabled.

Enable the Alerts bit.

Notification

LIM_NOTIFY is not high enough. Set equal to

MAX_NOTIFY.

Status options

STATUS_OPTS has Propagate Fault Forward bit set,

which should be cleared to cause an alarm to occur.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Rosemount 8800D Series

































































































































































































Search results

Summary of Contents for Rosemount 8800D Series

Reviews:

Emerson Rosemount 8800D Series, Reference Manual, Page: 82 / 192

Search results

Summary of Contents for Rosemount 8800D Series

Reviews: