155
electroluxicon.com
30" Combination Installation
planning
information
For models:
Built-In
Microwave
E30MO65GSS
Single Wall Oven
E30EW75GPS
E30EW75GSS
Note:
For planning
purposes only. Refer
to Product Installation
Guide on the web at
electroluxicon.com for
detailed instructions.
Specifications subject
to change.
Installation Specifications
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer
to product-specific electrical specifications on this page.)
•
Minimum 24" deep cutout dimension is critical for proper
combination install ation, to ensure that each built-in
product’s faceplate will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of
Wall Oven cutout to floor, 31" suggested.
•
Respect critical dimensions as noted for proper
installation of built-In products.
•
Minimum 23-1/4" clearance needed for Wall Oven
door depth when open.
30" Built-In Convection Microwave Specifications
•
Product Weight – 60 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.55 kW
(For use on adequately wired 120V, dedicated circuit
having 2-wire service with a separate ground wire.
Appliance must be grounded for safe operation.)
•
Amps @ 120 Volts = 13 Amps
•
Consult local building code in the event that cutout
opening may be required to be enclosed with sides,
ceiling and rear partition.
•
Full oven base of solid plywood or similar material
required, capable of supporting 100 Lbs.
•
Minimum 3-1/8" clearance required from bottom of Built-In
Microwave cutout to top edge of Wall Oven’s faceplate,
leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights –
(E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208
Volt, 60 Hertz AC only electrical supply with ground
required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts =
4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
Full oven base of solid plywood or similar material
required, capable of supporting 200 Lbs.
30" Combination Installation –
Built-In Microwave (w/Side Swing Door)
Electric Single Wall Oven
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
* Minimum 3
1
/
8
"
clearance required
from bottom of
Built-In Microwave
cutout to top edge of
Wall Oven’s faceplate,
leaving a 2"visible
gap between both
product faceplates
** Critical dimension –
MUST be applied
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
30" Built-In
Microwave Cutout
For model:
E30MO65GSS
24"min.
30"min.
3" max.
26
1
/
2
"min.
27"max.
28
1
/
2
"min.
28
7
/
8
"max.
Full plywood base
required to support
100 lbs.
28
1
/
2
"min.
29"max.
4"x 4" opening
to route armored
cable
120V/60Hz
grounded electrical
outlet should NOT
be located within
shaded area
19
7
/
8
"min.
20
3
/
8
"max.
24"min.**
(critical
dimension)
2" min.
31"
suggested
distance
4
1
/
2
"
min.
required
Bottom cutout
edge must be
finish cut
Full base required
to support 200 lbs.
Electrical junction
box location
2"
(visible
gap)*
5"
11
1
/
2
"
For Built-In Microwave / Single Wall Oven
Summary of Contents for ICON Professional E30DF74GPS
Page 1: ...design guide ...
Page 4: ...4 ...
