![background image](http://html1.mh-extra.com/html/ecg/esp-20101-black/esp-20101-black_instruction-manual_3877039012.webp)
English
English
12
Note:
When selecting the kettle size, it is recommended that the diameter be no less than 70 ± 5 mm. Keep
in mind that the volume of milk will approximately double. Make sure that the height of the kettle is
sufficient.
4. Insert the steam nozzle (with frothing wand) into the milk about 2 centimeters under the surface then turn
the knob in the position , steam nozzle starts to emit steam. Froth the milk by moving the kettle around
and up/down.
5. When done turn the knob in the position .
Note:
When the steaming stops, carefully clean the nozzle using a wet cloth or a sponge. Be careful, do not
damage the nozzle! Be careful, the nozzle is hot.
6. Pour frothed milk into the prepared espresso, now the cappuccino is ready. Enjoy your coffee! For diversity,
you can sprinkle the foam with a small amount of cocoa.
7. Press to turn off the machine's power switch.
NOTICE:
The water temperature in the boiler is too high after using the “steam” function for making coffee.
If you wish to brew coffee, it is recommended that you first drain the superheated water from the boiler
(let one cycle run in the “coffee” just with water).
Make sure that the button is in position (coffee) and turn the knob control in the position (coffee). Allow
one portion of coffee-free water to be pumped into the cup until the preheating light goes out.
After the heating light comes on again, you can start brewing coffee as described in the chapter "Espresso
preparation".
Note:
Use the same procedure when you use the steam for heating liquids.
Production of steam for heating liquids
Steam nozzle (without milk frothing attachment) can be used to heat beverages such as hot chocolate or water
by steam.
Note:
To heat liquids, remove the milk frothing attachment from the nozzle.
Steps:
1. Press the
ON/OFF
switch, the operation indicator lights up (red).
2. Place a suitable deep container with water under the nozzle to capture the steam. The nozzle should be
sufficiently immersed in the container. Carefully, the steam is hot.
3. Leave the button in the position (coffee) and switch the knob control in the position (coffee). When
the water starts streaming from the steam head, turn the knob to neutral position .
4. Press the steam button in position (steam) and wait, until the white preheat indicator lights up. Turn the
knob control in the position (steam). Allow water to flow from the nozzle until the desired temperature
is reached. Then return the knob in the neutral position .
If you are not going to use the machine, turn it off with the main switch and unplug it.
Tips for making good coffee
The following factors may affect the final quality and taste of the coffee:
Temperature
Cold lever with metal cup, filter and cup have a negative effect on the result.
Preheat the filter and the lever with metal cup in warm water and dry thoroughly.
Pour hot water in the cup and let it heat through. You can use the hot steam from the nozzle to heat the water
in the cup.
Summary of Contents for ESP 20101 Black
