E-FLITE BLADE CX2 Specifications Download Page 8 | Manualshive

Page: 8 / 48

background image

8

Battery Warnings and Guidelines

While the 7.V 800mAh -cell Lithium Polymer Battery Pack (EFLB0990) included with your

Blade™ CX features Charge Protection Circuitry and Balance Charging via the included

- to -Cell Lithium Polymer Balancing Charger (EFLC110) to help ensure a safe charge

every time, you MUST read the following safety instructions and warnings before handling,

charging or using the Li-Po battery pack.
Note: Lithium Polymer batteries are significantly more volatile than the alkaline, Ni-Cd or

Ni-MH batteries used in RC applications. All instructions and warnings must be followed

exactly. Mishandling of Li-Po batteries can result in fire.

By handling, charging or using the included Li-Po battery you assume all risks associated with lithium

batteries. If you do not agree with these conditions, return your complete Blade CX model in new,

unused condition to the place of purchase immediately.

•. You.must.charge.the.included.7 .4V.800mAh.2-cell.Li-Po.battery.pack.in.a.safe.area.away.from..

flammable.materials .

•. Do.not.charge.the.battery.when.installed.in.the.helicopter .

•. Never.charge.the.battery.unattended ..When.charging.the.battery.you.should.always.remain.in.constant.

observation.to.monitor.the.charging.process.and.react.to.potential.problems.that.may.occur .

•. After.flight,.the.battery.must.be.cooled.to.ambient.temperature.before.charging .

•.

You MUST use the included - to -Cell 7.-11.1V Li-Po Balancing Charger ONLY

..Failure.to.do.so.may.

result.in.a.fire.causing.personal.injury.and/or.property.damage ..

DO NOT use a Ni-Cd or Ni-MH charger

.

«
...
6
7
8
9
10
...
»

Summary of Contents for BLADE CX2

















































Reviews:

No comments

Related manuals for BLADE CX2

Brand: Jamara Pages: 4

Brand: Quadro Pages: 11

Brand: Faller Pages: 8

Brand: Faller Pages: 4

Brand: Black Horse Model Pages: 34

Brand: Sportsman Pages: 41

Brand: Eduard Pages: 3

M9780 Cadillac ESCALADE Custom Edition

Brand: Power Wheels Pages: 36

Outlaw JR. OBL 5123

Brand: THUNDER TIGER Pages: 12

GWR Meat Van Mica A/B NGSK0100

Brand: N Gauge Society Pages: 4

Brand: Falcon Pages: 81

Brand: BLOTZ Pages: 2

Brand: Makeblock Pages: 3

Seahorse Symphony 643415

Brand: Little Tikes Pages: 2

Pennsylvania 6-8-6 Bantam Turbine Steam Freight...

Brand: Rail King Pages: 24

Brand: LEGO Pages: 72

Brand: J. Perkins Pages: 12

Mario Kart Circuit Track Set

Brand: Hot Wheels Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands