E-FLITE BLADE CX2 Specifications Download Page 31

Page: 31 / 48

•. After.becoming.comfortable.with.hovering.the.Blade™.CX2.at.low-levels.of.altitude.just.a.few.inches.off.the.

ground,.you.can.transition.to.hovering.and.flying.the.helicopter.at.higher.altitudes.of.approximately.three.to.four.

feet ..At.these.higher.altitudes.you.will.be.able.to.get.a.feel.for.the.flight.characteristics.of.the.Blade.CX2.when.it.

is.flying.out.of.“ground.effect .”

•. If.at.any.time.during.flight.you.feel.like.the.helicopter.is.drifting.out.of.control,.simply.release.all.of.the.controls.

except.for.throttle ..You.will.need.to.use.the.throttle.to.maintain.altitude,.but.due.to.the.inherent.stability.of.the.

coaxial.counter-rotating.blades,.the.Blade.CX2.will.simply.return.to.a.stable.hover.on.its.own.if.space.allows .

•. Don’t.be.afraid.to.set.the.helicopter.down.on.the.ground.quickly.by.lowering.the.throttle.when.approaching.walls.

or.other.obstacles.to.help.prevent.main.rotor.blade.strikes ..Also,.the.optional.Training.Gear.Set.(EFLH1205).will.

help.to.further.prevent.damage.to.the.helicopter.in.the.event.that.you.must.make.an.abrupt.landing.to.avoid.walls.

or.other.obstacles .

• IN THE UNFORTUNATE EVENT OF A CRASH OR ROTOR BLADE STRIkE, NO MATTER

HOW MINOR OR MAjOR, YOU MUST LOWER BOTH THE THROTTLE (LEFT-HAND)

STICk AND THROTTLE TRIM TO THEIR LOWEST POSSIBLE POSITION AS QUICkLY AS

POSSIBLE TO PREVENT DAMAGE TO THE ESCS OF THE -IN-1 UNIT.

Failure to lower both the throttle stick and throttle trim to their lowest possible positions in the event

of a crash could result in damage to the main motor ESCs in the -in-1 unit, which may require

replacement of the -in-1 unit.
Note: Crash damage is not covered under warranty.

• It is extremely important when hovering and flying the Blade CX to be aware of the power level

of the Li-Po battery pack. If at any time the helicopter begins to require more throttle than typical

to maintain hover or flight, or has lost the ability to maintain hover or flight due to significant loss

of power, you must land the helicopter and power the motors down IMMEDIATELY to prevent

over-discharge of the Li-Po battery pack.
If you continue to run the motors after noticing a loss in power it is possible to discharge the Li-Po

battery pack too far, causing permanent damage to the pack. Over-discharge of the Li-Po battery

pack can result in shortened flight times, loss of power output or failure of the pack entirely.

•. Once.you.have.gained.experience.and.confidence.in.hovering.the.Blade.CX2,.you.can.attempt.more.advanced.

maneuvers.including:

Forward.Flight

Backward.Flight

Pirouettes

Skidding.Takeoffs

Skidding.Landings

Spot.Landings

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands